Iniciar sesión:
Votos - 2, Puntuación media: 4.5 ( )

Manual de usuario CDA, modelo 6Q5

Fabricar: CDA
Tamaño del archivo: 2.87 mb
Nombre del archivo: cccd8142-ff16-48a7-877b-6567e8da1fa3.pdf
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


Avoid using cleaning products with a chlorine or acidic base. WARNING When correctly installed, your product meets all safety requirements laid down for this type of product category. However special care should be taken around the rear or the underneath of the appliance as these areas are not designed or intended to be touched and may contain sharp or rough edges, that may cause injury. Inside of Oven The oven should always be cleaned after use when it has cooled down. The cavity should be cleaned using a mild detergent solution and warm water. Suitable proprietary chemical cleaners may be used after first consulting with the manufacturers recommendations and testing a small sample of the oven cavity. Abrasive cleaning agents or scouring pads/cloths should not be used on the cavity surface. NOTE: The manufacturers of this appliance will accept no responsibility for damage caused by chemical or abrasive cleaning. Enamelled Parts All the enamelled parts must be cleaned with a sponge and soapy water only or other non-abrasive products. Dry preferably with a micro fibre or soft cloth. IMPORTANT: Before any operation of cleaning and maintenance disconnect the appliance from the electrical supply. ATTENTION: Let the oven cool down and pay special attention no to touch the hot heating elements inside the oven cavity. 25 25 Stainless Steel, Aluminium, Painted Parts and Silk-screen Printed Surfaces Clean using an appropriate product. Always dry thoroughly. Stainless steel surfaces: can be cleaned with an appropriate stainless steel cleaner. IMPORTANT: these parts must be cleaned very carefully to avoid scratching and abrasion. You are advised to use a soft cloth and neutral soap. Glass Control Panel (Models with Glass Control Panel) Clean using an appropriate product. Always dry thoroughly. Do not use harsh abrasive cleaners or sharp metal scrapers to clean the control panel since they can scratch the surface, which may result in shattering of the glass. CAUTION: Do not use abrasive substances or non- neutral detergents as these will irreparably damage the surface. CAUTION: Do not use a steam cleaner because the moisture can get into the appliance thus make it unsafe. CAUTION: Do not store flammable material in the oven. CAUTION: Do not use harsh abrasive cleaners or sharp metal scrapers to clean the oven door glass since they can scratch the surface, which may result in shattering of the glass. 26 26 Replacing the Oven Light WARNING: Ensure the appliance is switched off before replacing the lamp to avoid the possibility of electric shock. – Let the oven cavity and the heating elements to cool down; – Switch off the electrical supply; – Unscrew the protective cover C (fig. 15); – Unscrew and replace the bulb B with a new one suitable for high temperatures (300°C) having the following specifications: 230V, E14 and same power (check watt power as stamped in the bulb itself) of the replaced bulb. – Refit the protective cover. NOTE: Oven bulb replacement is not covered by your guarantee. Fig. 15 Models: SC210.. SC220.. SC510.. SC610.. BC 27 Replacing the Halogen Oven Light WARNING: Ensure the appliance is switched off before replacing the lamp to avoid the possibility of electric shock. – Let the oven cavity and the heating elements to cool down; – Switch off the electrical supply; Top Right Lamp: – Remove the protective cover C (fig. 16); – Replace the halogen lamp B with a new one suitable for high temperatures having the following specifications: 230V and same power (check watt power as stamped in the lamp itself) of the replaced lamp. IMPORTANT WARNING: Never replace the bulb with bare hands; contamination from your fingers can cause premature failure. Always use a clean cloth or gloves. – Refit the protective cover; Left Lamp (Model "6Q5.." Only): – Remove the left wire rack by unscrewing the fixing screws. – Press down from the top the protective cover A (fig. 16) and remove it by rotating on the lower side. IMPORTANT: never use screwdrivers or other utensils to remove the cover A. This could damage the enamel of the oven or the lampholder. Operate only by hands. – Replace the halogen lamp B with a new one suitable for high temperatures having the following specifications: 230V and same power (check watt power as stamped in the lamp itself) of the replaced lamp. IMPORTANT WARNING: Never replace the bulb with bare hands; contamination from your fingers can cause premature failure. Always use a clean cloth or gloves. – Refit the protective cover A operating in reverse order. ATTENTION: the notch in the inner edge of the cover must be oriented toward the lamp. – Assemble the left wire rack. Note: Oven bulb replacement is not covered by your guarantee. Models: SV100.. SV150.. 6Q5.. Model: 6Q5.. ABBC12AAFig. 16 WRONG CORRECT 27 Replacing the Halogen Oven Light WARNING: Ensure the appliance is switched off before replacing the lamp to avoid the possibility of electric shock. – Let the oven cavity and the heating elemen...

Otros modelos de este manual:
Hornos Eléctricos - SC220 (2.87 mb)
Hornos Eléctricos - SC510 (2.87 mb)
Hornos Eléctricos - SC610 (2.87 mb)
Hornos Eléctricos - SV100 (2.87 mb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría