Votos - 2, Puntuación media: 3.5 ( )

Fabricar: Hobart Tamaño del archivo: 1.44 mb Nombre del archivo: Idioma del manual:

• To set the Probe Temperature, press and use the UP and DOWN arrows to adjust the setting. The Cooking Time cannot be used when the Probe Temperature is in use. NOTE: During Operator training to demonstrate use of the probe, place the probe in a container of water to simulate cooking of actual product. – 12 – TEMPERATURE PROBE APPLICATIONS TEMPERATURE PROBE APPLICATIONS °F Beef 140 160 170 Lamb 175 – 185 Pork Fresh 170 140 – 170 Turkey 185 170 Veal 170 ENTERING A COOKING PROGRAM 1. When entering cooking parameters, always select the Mode as the first element in a cooking phase: HOT AIR, STEAM, or COMBI (also, select Vent Closed or Open for HOT AIR mode and Steam Factor for COMBI mode). 2. Enter the finish parameter for the cooking phase (COOKING TIME or PROBE TEMP.) with its value. 3. Enter the oven control parameter for the cooking phase (TEMP or ) with its value. FAN Speed can be set at FULL or 1/2. 4. Steps 1, 2, and 3 complete the parameters for that phase. For any additional phase (or phases), press the PHASE 1 – 5 key. Repeat steps 1, 2, 3, and 4 for each cooking phase. 5. If programming a repeat cooking process, select a Program Number following the instructions for Programming Memory on the next two pages. 6. Press to start cooking; the indicator light in the Start Stop key indicates the oven is operational. 7. When finished, press again, to silence the buzzer. – 13 – PROGRAMMING MEMORY PROGRAMMING MEMORY If the numbered Program has not been programmed (or is vacant), the Time displays – h – – min. No Mode or Phase indicator lights are lit. The Temperature displays – – or the current temperature. To CREATE a new program — With — — in the program number display, the control is in Manual mode. 0 0 Press the key. Program Number 00 is displayed and the control is in Program Mode. Use UP or DOWN arrows to increase or decrease the program number until a vacant program number is found. ENTER THE COOKING INSTRUCTIONS (FOLLOW STEPS 1 – 6): 1) Select the cooking mode: Hot Air, Steam, or Combi. If Hot Air, select Vent (Closed or Open). If Combi, set Steam Factor. 2) Set either the Time or Probe Temperature. 3) Set the Oven Temperature or . Select Fan 1/2 speed or full. — — 4) End of the 1st Phase. Press to shift to the next phase. 5) Repeat steps 1 – 4 for as many of the 5 phases as are needed. Review the program by stepping through the phases. Make any needed changes. 6) When the program is set, save it in memory by pressing until the beep is heard. NOTE: A cooking program can also be entered in manual mode and saved to a program number by selecting the Program Number and pressing for about three seconds. To DELETE an existing program — With — — in the program number display, the control is in Manual mode. 0 0 Press the key. Program Number 0 0 is displayed and the control is in Program Mode. Use UP or DOWN arrows to increase or decrease the program number until the program number to be deleted is displayed. Press and hold it in for about three seconds until the beep sounds, indicating the program has been deleted. NOTE: If a previous program had been selected and was active in manual mode, it will be copied to the selected program number, replacing the previous program. Verify that the program number is vacant after you delete it. — — – 14 – To COPY an existing program to a NEWprogram number — To COPY an existing program to a NEWprogram number — Press to begin the program. Pause. Press to stop the program. Change the program number to the NEWnumber. Press until the beep sounds, indicating the program has been copied. To CHANGE a program — 0 0 With — — in the program number display, the control is in Manual mode. Press the key. Program number 00 is displayed. Use the UP or DOWN arrows to increase or decrease until the program number you want to change is displayed. Step through each phase, making any temperature, time or other changes for the phase; press to shift to the next phase. The program number begins to blink when one or more changes have been made to the program. To SAVE the changed cooking program, press and hold it in for about three seconds until the beep sounds. RECALLING A PROGRAM FROM MEMORY Once a menu item has been programmed, it can be recalled, reviewed and used to cook food. If the Program has already been programmed, its values are recalled from memory and displayed. You can view all the programmed information by stepping through the phases using the phase button. To RECALL a program from memory — With — — in the program number display, the control is in Manual mode. Press the 0 0 key. Program Number 00 is displayed. Use the UP or DOWN arrows to select the program number you want. Use the Phase 1 – 5 key to step-through and verify the cooking parameters for each phase of the cooking program. Load the oven. If using the probe, place it in the center of the product. Close the door and press to begin the cooking program. The blinking indicator light in the Phase 1 – 5 key shows which phase o...

Descargar ahora

Introduzca dos números de la imagen: