Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
thick. Clearance between the cooking surface and protected cabinets MUST NEVER BE LESS THAN 24 INCHES. The vertical distance from the plane of the cooking surface to the bottom of adjacent overhead cabinets extending closer than 1. to the plane of the range sides must not be less than 18.. (See the Dimensions and Clearances illustration in this section.) CAUTION: Items of interest to children should not be stored in cabinets above a range or on the backsplash of a range— children climbing on the range to reach items could be seriously injured. 40 Read these instructions completely and carefully. DIMENSIONS AND CLEARANCES Provide adequate clearances between the range and adjacent combustible surfaces. These dimensions must be met for safe use of your range. The location of the electrical outlet and pipe opening (see Gas Pipe and Electric Outlet Locations) may be adjusted to meet specific requirements. Depth with door closed (includes door handle) 28-1/4” to 29” Depth varies depending on model. See specifications sheet for your model. 30” 36-1/4” ± 1/4” 47-3/4” Depth with door open: 46-3/8” Height 30” 30” 6”Minimum Minimum clearance to right wall Minimum clearance to left wall 18” 6” Minimum to cabinets on either side of the range 36” To cabinets below cooktop and at the range back 0” Consumer SupportOperating InstructionsSafety Instructions InstallationInstructions Troubleshooting Tips 13” Maximum depth for cabinets above countertops Front edge of the range side panel forward from cabinet 0” 1/4” To cabinets below cooktop and at the range back 41 Installation of the range. Operating Instructions Safety InstructionsInstallationInstructionsTroubleshooting TipsConsumer Support TOOLS YOU WILL NEED Phillips and flat-blade screwdrivers Pencil and ruler Two pipe wrenches (one for backup) Open-end or adjustable wrench Nut driver or wrench: 1/4 . Drill ADDITIONAL MATERIALS YOU MAY NEED: Gas line shut-off valve Pipe joint sealant or UL-approved pipe thread tape with Teflon* that resists action of natural and LP gases. *Teflon: Registered trademark of DuPont Flexible metal appliance connector (1/2 . I.D.). A 5foot length is recommended for ease of installation but other lengths are acceptable. Never use an old connector when installing a new range. Flare union adapter for connection to gas supply line (3/4 . or 1/2 . NPT x 1/2 . I.D.) Flare union adapter for connection to pressure regulator on range (1/2 . NPT x 1/2 . I.D.) Liquid leak detector or soapy water. Lag bolt or 1/2 . O.D. Sleeve anchor (for concrete floors only). Squeeze Connector matching the size of the bracket opening (on the range back behind the wiring cover) and the house conduit. Obtain only if replacing the power cord with conduit. LOCATION GUIDELINES Do not locate the range where it may be subject to strong drafts. Any openings in the floor or wall behind the range should be sealed. Make sure the openings around the base of the range that supply fresh air for combustion and ventilation are not obstructed by carpeting or woodwork. Your range, like many other household items, is heavy and can settle into soft floor coverings such as cushioned vinyl or carpeting. Use care when moving the range on this type of flooring. It is recommended that the following simple and inexpensive instructions be followed to protect your floor. The range should be installed on a sheet of plywood (or similar material). When the floor covering ends at the front of the range, the area that the range will rest on should be built up with plywood to the same level or higher than the floor covering. This will allow the range to be moved for cleaning or servicing. Also, make sure your floor covering will withstand 180°F. (See the Installation Safety Instructions section.) Make sure the wall coverings around your range can withstand the heat generated (up to 200°F) by the range. (See the Installation Safety Instructions section.) IMPORTANT! Remove all tape and packaging. Make sure the burners are properly seated and level. Take the accessory pack out of the oven. Check to be sure that no range parts have come loose during shipping. 42 Read these instructions completely and carefully. Gas Supply Requirements Recommended Gas Pipe Outlet Locations Gas Supply Requirements Recommended Gas Pipe Outlet Locations 7-1/2” 9” 3” 30” 3” Recommended area for through-the-wall connection of pipe stub/shut-off valve. Recommended area for through-the-floor connection of pipe stub/ shut-off valve. 2” This area allows flush installation to rear wall. NOTE: Make gas connections on the left side of the cutout opening. Provide Adequate Gas Supply Your range is designed to operate at a pressure of 5. of water column on natural gas or, if designed for LP gas (propane or butane), 10 . of water column. Make sure you are supplying your range with the type of gas for which it is designed. This range is convertible for use on natural or propane gas. If you decide to use this range on LP gas, co...