|
Resumen del manual
Continuously recharging will reduce life of batteries. If razor has not been used for at least 1 month, razor must be recharged for a full 16 hours. Do not charge razor in pouch (model 3605X only). 1 2 3 Stretch your skin with your free hand so blades can lift and cut whiskers. Gently press razor to skin. Turn razor OFF. Put the protective razor head cap on the razor to protect razor heads. Replace your Norelco Double Action razor heads (model # HQ4) once a year for optimal shaving results. SHAVING Use your new razor exclusively for 3 weeks to fully enjoy the closeness of a Norelco shave. * At first you may not get as close a shave as you expect, or your face may even become slightly irritated. This is normal since your beard and skin will need time to adjust. Invest 3 weeks and you'll soon experience the full joy of your new razor. * Stick with it! If you alternate shaving methods during the adjustment period, it may make it more difficult to adapt to the Norelco shaving system. Shaving with skin dry gives the best results. Turn razor ON. Shave against the direction of beard growth using both straight and circular movements. 1 2 3 4 5 6. 7. 4 5 TRIMMING To groom sideburns and 1 Turn razor ON. 2 Push up Trimmer Slide Switch. 3 Hold Trimmer as shown and move in downward strokes with gentle pressure. 4 Close Trimmer by sliding Trimmer switch down. 5 Turn razor OFF. CLEANING Once A Week: Razor 1 Turn razor OFF. 2 Clean the top of the razor with the supplied brush. 3 Remove Razor Head Assembly from the razor unit. Brush the inside of housing Assembly. Replace the Razor Head Assembly back on razor. Every Two Months: Razor Heads Turn razor OFF and disconnect from outlet. Remove Razor Head Assembly from housing unit. Brush the inside of the housing. Turn Razor Head Assembly over so that the underside is exposed. Press down and turn wheel of frame counterclockwise. Remove the frame and brush clean. 1 2 3 4 5 6 8. 7 Slide and remove one cutter and head • Be careful not to mix up cutters They are a matched set and if interchanged, it will greatly affect shaving performance. 8 Separate the cutter from the head. 9 Only brush the cutter in an upward motion. Use the short bristled side of the brush. 10 Brush the slots of the razor head. For optimum performance, razor cutters and heads should be cleaned in a degreasing liquid (e.g. Norelco Razor Cleaner or alcohol) and lubricated with Norelco Razor Lubricant, model AL80, or one drop of mineral oil (in the center of the head). 11 Replace the cutter into head section. Slide razor head back into frame making sure that flat rim of cutting heads slides under 2 clamps on frame. 12 Repeat the process for the other two razor heads (cutters and heads). 13 Replace the frame. 9. 14 Press down and turn the wheel into place. 15 Replace the Razor Head Assembly back on razor. After Each Use: Trimmer 1 Turn razor OFF. 2 Push Trimmer Slide Switch up to pop-up Trimmer. 3 Clean Trimmer with the brush every time you use it. 4 Lubricate the Trimmer teeth with Norelco Razor Lubricant (model AL80), or with one drop of mineral oil every 6 months. 5 Close Trimmer by sliding Trimmer switch down. 10. ASSISTANCE For assistance or the Authorized Norelco Service Location nearest you, call toll free: 1-800-243-3050 or visit our website: Authorized Norelco Service Location information is available 24 hours a day, 7 days a week. ACCESSORIES Replacement Heads • Model HQ4 - For maximum razor performance, replace your Norelco Double Action razor heads once a year. Razor Cleaners • ERC100 - Norelco RAZORMATE ® Electrosonic Heads Cleaner • RC1776 - Norelco Razor Cleaner Razor Lubricant • AL80 - Norelco Razor Lubricant Norelco Razor Accessories may be purchased at a store near you, an Authorized Norelco Service Location or by the order form ...
Otros modelos de este manual:Eléctrico - 3601X (176.72 kb)
Eléctrico - 3605x (176.72 kb)