Votos - 0, Puntuación media: 0
(
)
)
|
Resumen del manual
-Water may leak from the socket at the bottom of the shaver when you rinse it.This is normal and not dangerous because all electronics are enclosed in a sealed power unit inside the shaver. -Do not use the shaver, Jet Clean System, adapter, charging stand or any other par t if it is damaged, as this may cause injur y. Always replace a damaged adapter, charging stand or par t with one of the original type. -Use, charge and store the shaver and the Jet Clean System at a temperature between 10°C and 35°C. -Always place and use the shaver and the Jet Clean System on a surface that is fluid-resistant. -Only use the adapter, charging stand and accessories supplied. -Always put the protection cap on the shaver to prevent damage and to avoid dir t accumulation in the shaving heads. -Only use the Jet Clean System with the original Jet Clean solution (HQ200). -Always place the Jet Clean System on a stable, level and horizontal surface to prevent leakage. -When the Jet Clean System is ready for use, do not move it to prevent leakage. -The Jet Clean System thoroughly cleans but does not disinfect your shaver, therefore do not share the shaver with others. -Empty the cleaning chamber of the Jet Clean System and clean the cleaning chamber thoroughly by rinsing it with hot tap water ever y 15 days. -If the shaver and the Jet Clean System are subjected to a major change in temperature, pressure or humidity, let them acclimatise for 30 minutes before you use them. English Compliance with standards -This Philips appliance complies with all applicable standards and regulations regarding exposure to electromagnetic fields (EMF) can be safely cleaned under the tap. general -The appliance is equipped with an automatic voltage selector and is suitable for mains voltages ranging from 100 to 240 volts. -The adapter transforms 100-240 volts to a safe low voltage of less than 24 volts. Charging It takes approx. 1 hour to fully charge the shaver. When you charge the shaver for the first time or after a long period of disuse, let it charge until the white batter y lights up continuously. A fully charged shaver provides up to 60 (PT927CC/PT927/ PT925/PT923/ PT923CC/PT920) or 50 shaving minutes (PT877/PT876/PT875/PT870). The shaving time may be less than 60(PT927CC/PT927/PT925/PT923/ PT923CC/PT920) or 50 shaving minutes (PT877/PT876/PT875/PT870) as a result of your shaving behaviour, your cleaning habits or your beard type. Charge indications Battery low -When the batter y is almost empty (when there are only 5 or fewer shaving minutes left), the batter y light star ts to flash orange. -When you switch off the shaver, the batter y light continues to flash orange for a few seconds. Quick charging -When you star t charging the empty batter y, the batter y light flashes white and orange. Note:When the battery light flashes white and orange towards only white, you can have a quick shave of three minutes. Charging -When the shaver is charging, the batter y light flashes white. English Battery fully charged -When the batter y is fully charged, the batter y light lights up white continuously. Note: After approx. 30 minutes, the battery light goes out to save energy. Charging with the adapter Do not charge the shaver in a closed pouch (PT927CC/PT927/PT925/ PT923CC/PT923/PT920/PT877 only). 1 2 Put the small plug in the shaver. Put the adapter in the wall socket. The battery symbol show the charging status of the shaver (see , section ‘Charge indications’ in this chapter). Charging in the charging stand (PT927/PT925/PT923/PT920/ PT876/PT875 only) 1 2 3 Put the small plug in the charging stand. Put the adapter in the wall socket. Place the shaver in the charging stand. The battery symbol show the charging status of the shaver (see , section ‘Charge indications’ in this chapter). Charging in the Jet Clean system (PT927CC/PT923CC only) 1 2 3 Put the small plug in the Jet Clean System. Put the adapter in the wall socket. Place the shaver without protection cap upside down in the shaver holder. Note:The shaver cannot be placed in the Jet Clean System when the protection cap is on the shaving unit. 10 English 4 Push down the locking lever completely to lock the shaver into place. The battery symbol on the Jet Clean System flashes to indicate that , the shaver is being charged. Note:When the Jet Clean System is performing the cleaning program, the battery symbol is out. When the battery is fully charged, the battery symbol on the Jet , Clean System lights up continuously. Note: After approx. 30 minutes, the battery symbol goes out to save energy. 5 To remove the shaver from the Jet Clean System, move the locking lever upwards until it does not go any further and remove the shaver. Using the shaver Note:You can also use the appliance directly from the mains. Simply connect the shaver to the mains. shaving 1 2 Press the on/off button once to switch on the shaver. Move the shaving heads over your skin. Make circular movements. -Your skin may need 2 or 3 wee...
Otros modelos de este manual:Eléctrico - PT927/21 (4.63 mb)