Reach under the driver's side dash and unclip the temperature control cable. Using Metra's 86-5618, pull the factory radio/climate control panel from the dash. Disconnect the switch power harness, antenna plug, radio/speaker power harnesses and vacuum hose harness. 2 CONTROL PANEL) Turn the integrated control panel over and disconnect the vent control harness ("A"), fan speed control harness ("B"), and defroster harness ("C"). Unclip the main switch harness from the side of the factory unit.

. .. . . . .. . . . . . . . .. . . . .. . . . .. . . . .1 Kit Preparation .. . . . . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . .. . . . . . . 2 Kit Assembly -DIN Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 -ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . .4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 *Note# Refer also to the instructions included w

Using the hardware included with the equalizer, mount the unit to the kit. (see Fig. A) IF AN EQUALIZER WILL NOT BE INCLUDED: Snap the Equalizer Dummy Plate into the Radio Housing, (see Fig. B) A) Strip wire ends back 1A" B) Twist ends together C) Solder D) Tape Locate the factory wiring harness in the dash. Metra recommends using the proper mating adaptor and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit).

Metra recommends making connections as shown using the supplied wire harness. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit). Right Front +......... ......Gray Right Front -........... Gray/Black Left Front +............ White Left Front -.............. .....White/Black Right Rear +........... ......Violet Right Rear-............. .....Violet/Black Left Rear +.............. .....Green Left Rear-................ Green/Black 12 Volt Po

INSTALLATION INSTRUCTIONS FOR PART 99-2008 INSTALLATION INSTRUCTIONS FOR PART 99-2008 99-2008 APPLICATIONS Cadillac DTS 2006-2010 Cadillac SRX 2007-2009 KIT FEATURES • DIN Radio Provisiion with Pocket • ISO Mount Radio Provisiion with Pocket • Double DIN Radio Provisiion • Stacked ISO Mount Units Provisiion A) Radio Housing • B) ISO Trim Plate • C) ISO Brackets • D) Double DIN Trim Plate • E) Double DIN Brackets • F) Pocket KIT COMPONENTS A DCBEFTOOLS REQUIRED: WIRING AND ANTENNA CONNECTIONS (So

.1 Kit Preparation....................................... .2 Kit Assembly - Double DIN Radio Provision ... ............................ .3 -Stacked ISO Mount Units Provision .......................... 3 Final Assembly ...........................................4 *Note: Refer also to the instructions included with the aftermarket radio. 95-8224 DASH DISASSEMBLY Toyota Matrix/Pontiac Vibe 2009-10 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unclip

............................ .3 -Stacked ISO Mount Units Provision .......................... 3 Final Assembly ...........................................4 *Note: Refer also to the instructions included with the aftermarket radio. 95-8152 DASH DISASSEMBLY LEXUS GS 300/400 1998-2005 1 Disconnect the negative battery terminal to prevent an accidental short circuit. 2 Unsnap and remove vent/clock assembly from above climate controls. (Figure A) 3 Remove two screws from behind vent/clock as

2006-20091-800-221-0932 ©2004-2009 METRAELECTRONICSCORPORATION70-1727INSTALLATIONINSTRUCTIONS HONDA CIVICwith Premium Sound SystemAMPBypassHarnessIn 2006 Honda Civics that have the Premium Sound System, there is an amplifier that drives all the speakers. This harness is designed to bypass the factory amplifier so to allow the user to use aftermarket amplifiers or to wire to the aftermarket radio. 2006-20091-800-221-0932 ©2004-2009 METRAELECTRONICSCORPORATION70-1727INSTALLATIONINSTRUCTIONS HONDA