Votos - 2, Puntuación media: 3
(
)
)
|
Resumen del manual
LCD screen The LCD screen displays the current settings, including the ambient room temperature, the selected mode or heat setting, and the timer icon if activated. It features a blue backlight for easy adjustment in the dark. Remote control The handy remote allows you to control the heater from wherever you are in the room. Switch the unit on or off, adjust the heat or temperature setting, activate the oscillation, or set the timer, all at the touch of a button. Batteries are included. Instant tip over cut out The instant tip over cut out interrupts the power to the heating element and fan if the heater is accidentally tipped over. The heater will not resume operation until it is replaced in the upright position. Safety auto shut off The safety auto shut off system detects any abnormally high temperatures within the heater and automatically switches it off to prevent overheating. Using your Oscillating Digital Ceramic Heater 1. Place the heater on a flat level surface and ensure that the air intake and air outlet are clear of obstructions. 2. Insert the plug into a 230-240V power outlet and turn the power on. 3. Move the on/off switch at the rear of the unit to the on (I) position. A beep will sound. 4. Press the power button on the control panel to turn the heater on. The LCD will display the current room temperature and HIGH, indicating that it is operating in HIGH heat mode. Fig. 2 5. Press the MODE button to cycle through the various operating modes: LOW – the heater will continuously run at its low wattage. AUTO - the digital thermostat will cycle the heater on and off to maintain your selected temperature. See instructions on setting the digital thermostat below. HIGH - the heater will continuously run at its high wattage. 6. To turn the heater off, press the power button on the control panel. The heater will stop operating. 7. Move the on/off switch at the rear of the unit to the off position (O). Turn the power off and remove the plug from the power outlet when not in use. Setting the digital thermostat 1. Press the mode button to select AUTO mode. AUTO will appear on the LCD screen, and the current room temperature will flash. 2. Use the Temp + and – buttons to select the desired temperature setting. SET, TEMP and the selected temperature will flash several times to indicate that the thermostat is set. The LCD will return to displaying the room temperature. 3. Once the room temperature reaches 3°C above the selected temperature, the heater will operate for a further 20 seconds and then cutout. When the room temperature drops below the set temperature, the heater will switch back on. The thermostat will continue to cycle the heater on and off to maintain your selected temperature. 4. To view the set temperature, press the Temp button. The set temperature setting will flash on the screen. 5. To turn the heater off, press the power button on the control panel. The heater will stop operating. 6. Move the on/off switch at the rear of the unit to the off position (O). Turn the power off and remove the plug from the power outlet when not in use. Using your Oscillating Digital Ceramic Heater (continued) Activating the Oscillation function Press the OSC button on the control panel or remote to activate the oscillation. The heater will continue to oscillate from side to side, distributing warm air around the room, until the OSC button is pressed again. The body of the heater will stop oscillating in its current position. To align the heater body and base, press the OSC button to activate the oscillation, and press it again when the two parts are aligned. Setting the timer 1. Set the heater to the desired heat or temperature setting as per the instructions above. 2. Press the timer button once to set the heater to switch off after one hour, twice for 2 hours and so on, up to 8 hours. The timer icon will appear on the screen, as shown in figure 3. The heater will continue operating for the selected number of hours and will then switch off automatically. AUTO ROOM TEMP Fig. 3 Using the remote control The buttons on the remote control function in the same way as the buttons on the control panel. It is powered by 2 x AAA batteries. Note: when using the oscillating function in AUTO mode the heater will stop oscillating when the selected temperature is reached and the unit cycles off. It will resume oscillating when the heater cycles back on to maintain the selected temperature level. Resetting the safety auto shut off Your Oscillating Digital Ceramic heater is equipped with a safety system that detects any abnormally high temperatures within the heater and automatically shuts it off to prevent overheating. Should the safety auto shut off activate and switch the heater off, it will need to be reset. To reset the heater: 1. Move the on/off switch at the rear of the heater to the off position (O). 2. Unplug the heater and wait 5-10 minutes for the unit to cool down. 3. After 5-10 minutes, plug the heater in again an...