Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
When writing, always give the full model number which is on the nameplate attached to the inside of the cabinet door of the heater. When ordering repair parts or options, always give the following information as shown in this list: 1. The PART NUMBER 2. The PART DESCRIPTION 3. The MODEL NUMBER: 2941 4. The SERIAL NUMBER:________________ Before installing your heater, fill in the serial number of your heater in the space provided above. OWNERS MANUAL Model 2941 WONDERWOOD THERMOSTAT CONTROLLED WOOD BURNING CIRCULATOR *ASSEMBLY *INSTALLATION *OPERATION *REPAIR PARTS WONDERWOOD SAFETY NOTICE: If this heater is not properly installed, a house fire may result. For your safety, follow the installation directions. Contact local building or fire officials about restrictions and inspection requirements in your area. CAUTION: Read all instructions carefully before starting the installation or operation of this heater. Improper installation may void your warranty. DO NOT USE THIS HEATER IN A MOBILE HOME OR TRAILER United States Stove Company 227 Industrial Park Rd. P.O.Box 151 South Pittsburg, TN 37380 (423) 837-2100 Tested to UL 1482 & CAN/ULC-S627 United States Stove Company 227 Industrial Park Rd. P.O.Box 151 South Pittsburg, TN 37380 (423) 837-2100 COMPANYUNITEDSTATESSTOVECSSU 85947-J TOOLS AND MATERIAL NEEDED TOOLS Pencil 6 Foot Folding rule or tape Tin Snips Drill, hand or electric Drill bit, 1/8" dia. (for sheet metal screws) Gloves Screwdriver (blade-type) 5/16" Nut Driver or 5/16" Socket w/Ratchet MATERIALS Chimney Connection- 6" Dia. Black Steel (24 Ga. minimum): Straight or corrugated elbow (as required)* 1/2" Sheet Metal Screws 6" Inside Diameter Underwriters Laboratories (UL) listed Residential Type and Building Heating Appliance Chimney, Type "HT", or 6" existing Masonry Chimney with flue liner. Floor Protector Material: 3' x 4'-6" as specified on page 4. Furnace Cement (Manufacturer recommends: Rutland Code 78 or Equivalent) * Avoid adjustable elbows, they leak! CIRCULATOR DIMENSIONS Fig. 1 32 1/4 12 1/2 33 1/2 4 1/8 4 1/419 1/4 CENTER LINE OF 6" CHIMNEY CONNECTOR 24 TOP OF FLOOR PROTECTOR CENTER LINE OF 6" CHIMNEY CONNECTORWONDERWOOD RULES FOR SAFE INSTALLATION AND OPERATION Read these rules and the instructions carefully. SAFETY NOTICE: If this heater is not properly installed, a house fire may result. For your safety, follow the installation directions. Contact local building or fire officials about restrictions and installation inspection requirements in your area. 1. Check local codes. The installation must comply with their rulings. Do not install this heater in a mobile home or trailer. 2. Always connect this heater to a chimney or vent to the outside. Never vent to another room or inside a building. 3. Do not connect a WOOD burning heater to an aluminum Type B gas vent. This is not safe and is prohibited by all codes. This 2 heater requires connection to approved chimneys: Either a factory built 6" UL 103HT or a lined and approved and recently in spected and cleaned masonry chimney with a 6" flue, preferably round. A larger masonry flue may be used, so long as the flue-section diameter is not greater than 50 sq. in. The chimney portion (whether factory-built F36 BLOWER KIT An Optional Blower kit is available for the 2941 Wonderwood automatic wood burning circulator heater. If this kit is not available where you have purchased this Wonderwood heater, you can purchase the F36 Blower Kit directly from the factory. To order contact the United States Stove Company at the address and telephone number given on the back page. 19 NOTE: DURING OPENING AND CLOSING OF THE FEED AND ASH DOORS OF THIS HEATER, IT MAY SEEM THAT THE FIT OF THE DOOR IS "TOO TIGHT". AS THE HEATER IS FIRED, THE GASKETING "SETTLES" OR "SEATS" ITSELF IN THE DOOR. THE TIGHT FIT AT THE FACTORY AND BEFORE THE HEATER'S INITIAL FIRING IS TO INSURE A GOOD SEAL AFTER THE GASKETING "SETTLES". NOTE: FOR YOUR SAFETY, WE RECOMMEND INSTALLING SMOKE DETECTORS IN YOUR HOME IF NOT ALREADY INSTALLED. SAFETY NOTICE In the unlikely event that your 2941 "overfires" (a condition evidenced by elbows, stovepipes, and connectors glowing red in appearance or otherwise discoloring), then your installation is subject to excessive draft created by either a chimney too tall or too great in diameter in conjunction with its height, or some other factor of an indeterminate cause. In this event, you should install a barometric draft regulator. Such installation will preclude any overfiring and/or any hazardous consequences of potential overfiring. Barometric draft regulators are generally available where you purchased your stove or may be ordered directly from United States Stove Company at a nominal charge. 2001 Consumer Price: $24.00 - Includes Shipping and Handling BAROMETRIC DRAFT REGULATOR Model DR6 18 or masonry) must be tall enough to provide sufficient draft and safe exit of smoke and combustion products. Please refer to Page ...