Votos - 3, Puntuación media: 4 ( )

Fabricar: Sears Tamaño del archivo: 3.24 mb Nombre del archivo: Idioma del manual:

In some cases, additional length will be required for this hose. Use the Black plastic 1/2" OD barbed coupling and a suitable section of 1/2" ID hose to make the connection. Secure all connections with clamps Connect the 3/16" ID relief tube from the small port on the Trap to the top port of the transition as shown in the picture. In some 44001 102004 NOTE_. Bw]t-in channel will be angled 5° to 10° also. Dual Pressure Switch 3/16"ID On Some Models ONLY INLET _) 4= Connector, 3/16" OD (loose parts hag) Relief Tube, -Extension Black, 3/16"ID Cut to fit (loosepartsbag) 1_ TrapConnection © Preassemble & insert into furnace 25-24-45 cases, additional hose length will be needed. Use the clear plastic 3/16" OD flexible tubing connector and a suitable length of extra 3/16" ID hose to make this connection. Install the vent pipe grommet into the casing Cut an appropriate length of 2" PVC pipe long, enough to exit the cabinet and connect the vent drain • A standard field supplied 2" els), or • A 2" PVC coupling fastened models) Install Tee Trap into bottom section Connect the Tee trap and the main shown in Figure 18. to either: PVC tee (N9MP1 and 2 mod- onto the Drain Tee (*9MPD of Tee. drain line exiting the casing as Note: It is recommended that all PVC piping and fitting connections be fit up and inspected before final cementing. Both the external Trap and the external Tee Trap must be primed before operation. Verify all condensate drain connections are securely clamped. A coupling and clamps (in loose part bag) may be installed as shown for future servicing of the vent system. E_ Downflow Right Side Vent and Trap Yellow or black Plastic Cap Trap Connection _Clamp ears '_ ointed OUT / Vent Drain Pmassemble& & Clamps insert intofurnace 3/16" ID SIDE VIEW Rubber Tube ,_Rotate downward Splice Connector Coupling & Clamps 112"ID Barbed Drain Hose & Clamps Dual Pressure Switch On Some NOTE.'_Built-in channel will be angled 5° to 10° also. 2" PVCCoupling ModelsONLY Single Pressure Switch Detail Either:The PVC supplied 2" PVC Tee Drain TubeBlack, sis" ID Corrugated PVC3/4" WARNING White PVC Move Caps (loose partsbag) to top of trap Drain Tube, (&Clamps) Black, s/8" ID Cut to fit (looseparts bag) 25-24-46 Downflow Right Side Vent and Trap (SeeFigure 13) Remove the Drain Tee if installed. Install the vent pipe grommet into the casing Disconnect the hoses from the Trap assembly, and remove Trap Cut an appropriate length of 2" PVC pipe long, enough to exit the and Trap mounting bracket from the blower compartment. Using cabinet and connect the vent drain to either: cover plate and gasket provided in the loose parts bag, cover the • A standard field supplied 2" PVC tee (N9MP1 and 2 mod- hole from the burner compartment to the blower compartment and els), or secure with screws. • A 2" PVC coupling fastened onto the Drain Tee ('9MPD Move the caps to the top of the Trap and mount the Trap externally models) to the right side of the unit using the 2 screws provided. Install Tee Trap into bottom section of Tee. Connect the corrugated Drain Tube from the transition box to the Trap as shown. If an extension is required, use the black PVC tube Connect the Tee trap and the main drain line exiting the casing as connector and the black 5/8" ID Drain Tube in the loose parts bag. shown in Figure 18. Cut tube to length. Secure all connections with clamps. Note: It is recommended that all PVC piping and fitting connec- Connect the drain hose from the Vent Drain to the Trap. If an ex-tions be fit up and inspected before final cementing. Both the extension is required, use the black 1/2" OD barbed coupling, con-ternal Trap and the external Tee Trap must be primed before nect a black 1/2" ID elbow tube and a suitable section of a 1/2" ID operation. Verify all condensate drain connections are securely drain tube to make connection from the vent drain to the trap. Se-clamped. A coupling and clamps (in loose part bag) may be cure all connections with clamps. installed as shown for future servicing of the vent system. [_ 440 01 1020 04 Vent Drain & Clamps Horizontal Left Thru Top Yellowor blackPlastic Single Pressure Switch Detail _ Trap Connection %lamp ears" Pointed OUT Alternate Orienation Preassemble & insert into furnace 3116" ID Dual Pressure Switch _Rubber Tube ] _ Relief Tube Extension _I _ ReliefTube ' i _io16"neODtoFr lexibletubing 1/2"ID Drain Hose& Field (Optional) ClampsSuppliedTee TubeBlack, /8 ID Corrugated Cut at straight section TeeTrapWhite PVC Cap and Clamp (loose parts bag) Open End Leaveroomfor clamp Cut Here 25-24-47 Horizontal Left-Thru Top (SeeFigure14) Disconnect the hoses from the Trap assembly, and remove Trap and the black 3/16" ID relief tube in the loose parts bag. Cut tube and Trap mounting bracket from the blower compartment. Using to length. Secure all connections with clamps. cover plate and gasket provided in the loose parts bag, cover the Cut an appropriate length of 2" PVC pipe, long enough to exit the hole from ...

Descargar ahora

Introduzca dos números de la imagen: