Iniciar sesión:
Votos - 4, Puntuación media: 4.3 ( )

Manual de usuario Omega Vehicle Security, modelo SEPHB Series

Fabricar: Omega Vehicle Security
Tamaño del archivo: 320.66 kb
Nombre del archivo: M3661.pdf
Idioma del manual:en
Enlace gratuito para este manual disponible en la parte inferior de la página



Resumen del manual


2 Important Safety Instructions……………...................... 3 Prior to Installation........................................................ 4 Mounting Your Heating Blanket..................................... 5 Connecting Your Heating Blanket to a Power Source... 6 Troubleshooting Guide.................................................. 7 Warranty........................................................................ BACK Return Requests / Inquires........................................... BACK INTRODUCTION Thank you for purchasing this silicone rubber heating blanket. Your heater is designed to provide a long and efficient service life with function, reliability, and safety in mind. For successful operation of these heaters, read and understand these instructions prior to use. SAFETY ALERT SYMBOL Immediate hazards which WILL result in severe personal injury or death The symbol above is used to call your attention to instructions concerning your personal safety. It points out important safety precautions. It means “ ATTENTION! Become Alert! Your Hazards or unsafe practices which COULD result in Personal Safety is involved! ” Read the severe personal injury or death message that follows and be alert to the possibility of personal injury or death. Hazards or unsafe practices which COULD minor personal injury or property damage. SAVE THESE INSTRUCTIONS! Additional copies © Copyright 2006 ENGINEERING, All rights reserved. This document may reproduced, translated, prior written ENGINEERING, IMPORTANT SAFETY INSTRUCTIONS A person who has not read and understood all installation instructions is not qualified to install this product. FMAPPROVEDApprovals valid only when installed in accordance with all applicable instructions, codes, and regulations. Agency Approvals Hazardous Locations Class I, Division 2, Groups A, B, C, & D Class II, Division 2, Groups F & G SSHB series SEPHB series SRMU series up to 358.F (181.C) 73/23/EC (Low Voltage Directive) 73/23/EC (Low Voltage Directive) © Copyright 2006 ENGINEERING, All rights reserved. This document may reproduced, translated, prior written ENGINEERING, • Do not immerse heater in liquid. • Keep volatile or combustible material away from heater when in use. • Use heater only in approved locations. • Keep sharp metal objects away from heater. • All SEPHB blankets have T ratings described in Article 501 of the NEC code. The blankets should not be used in an area with a lower T rating than the blanket. The T rating is stated in marking on the blanket. Failure to observe these warnings may result in electric shock, risk of fire, and personal injury. End User Must Comply to the Following: • Only qualified personnel are allowed to connect electrical wiring. • Disconnect all supply power at the source before making any power connections. • All electrical wiring must follow local electrical codes and highly recommend following NEC Article 427. • Final installation / wiring is to be inspected by the authority who has jurisdication in the area that the heater is installed. • The end-user is responsible for providing a suitable disconnecting device. • The end-user is responsible for providing suitable electrical protection device. It is highly recommended that a ground fault circuit breaker is used. • SEPHB series: A NRTL (National Recognized Testing Laboratory) listed temperature controller with a failure annuciation must be used to the surface temperature of the blanket. The controller must be approved for the is located. • SEPHB series: If heater is used material, an auxiliary temperature sensing the contents of the used to avoid overheating Failure to observe personal injury or • Never handle the heater while it is in operation; always disconnect the heater from the power source and allow to cool prior to handling. • Inspect heater before use. • Never operate heater without a temperature control device. • Do not wrap the heater over itself • If spillage of foreign matter onto heater occurs, disconnect from power source and clean after heater is allowed to cool. • Never operate a heater without an appropriate heat sink (device being heated is considered a heat sink). • Do not operate heater above rated temperature...

Otros modelos de este manual:
Eléctrico - SSHB (320.66 kb)
Eléctrico - SRMU (320.66 kb)

Comentarios



Tu reseña
Tu nombre:
Introduzca dos números de la imagen:
capcha





Categoría