Votos - 3, Puntuación media: 3.3
(
)
)
|
Resumen del manual
Main Burner shuts off and Pilot 1. Insufficient fresh air. flame goes out while in operation. 2. Incorrect inlet supply pressure. 1. Determine that adequate ventilation exists to provide sufficient fresh air. Open a window or provide additional ventilation. (See Fresh Air Requirements, Pages 7-8) 2. Call local gas supplier. Adjust inlet supply pressure to specification: NG; 5.5” w.c.-14.0”w.c. LP; 11.0” w.c.-14.0”w.c. 20004555 19 Radiance Vent-Free Gas Heater Maintenance The following procedures will help ensure that your heater continues to perform safely and efficiently. Firebox Cleaning and Inspection Cleanliness is critical to correct operation of the heater. The log set, burner, valve controls and air circulation areas must all be kept free of dust and unobstructed by debris. Inspect these areas before each use and clean whenever accumulation is evident. Follow the simple procedure outlined below. Frequent cleaning may be necessary in living environments subject to excessive carpet lint or pet hair. For example, if you live with a dog that sheds continuously, you will need to inspect the burner area frequently and clean it as often as the accumulation requires. In extreme conditions, it may be necessary to clean the burner and log set monthly or bi-weekly. This appliance should be inspected and thoroughly cleaned annually by a qualified gas technician. Cleaning Procedure 1. Turn the burner OFF and let the heater cool completely before cleaning. 2. Lift the Front plate up and then swing the bottom out to disengage it from the heater shell. (Page 9, Fig. 5) 3. Remove the screen by lifting up and away from the unit. Or, if so equipped, remove the glass panel by releasing the two upper retainer latches. Lift the panel up and off of the firebox frame. (Fig. 35) 4. Carefully inspect the log set for damage. Contact your local dealer if any damage is evident. DO NOT OPERATE THE HEATER WITH A DAMAGED OR LOOSE LOG SET. Use a soft-bristled brush vacuum cleaner attachment to remove dust or debris from the log set, pilot and burner. Use care as the log set is fragile. 5. Inspect the catalytic combustor at the top of the firebox. Replace the combustor if any damage or deterioration is evident. 6. Replace the screen or glass panel and the front plate. DO NOT OPERATE THE HEATER WITH THE SCREEN / GLASS PANEL OR FRONT PLATE REMOVED. Fig. 35 Remove the screen or glass panel. Screen Hooks Glass Latch ST675 Glass Replacement If so equipped, do not operate this appliance with the glass panel cracked, broken, or removed. Replace damaged glass only with CFM Specialty Home Products ceramic glass panel Part No. 1601290. Follow the Cleaning Procedure instructions regarding parts removal. Care of Cast Iron An occasional dusting with a dry rag will help keep the painted surfaces looking new. Use high-temperature stove paints, available through your local dealer, to touch-up areas as needed. Clean areas to be painted with a wire brush and be sure to cover the log set, burner and valve assembly. Apply the paint sparingly; two light coats of paint will give better results than a single heavy coat. Porcelain enamel surfaces should be cleaned with a soft, damp cloth. Do not use abrasive cleaning agents. If necessary, use only a cleaning agent formulated specifically for use on porcelain enamel surfaces. WARNING Turn the burner Pilot OFF before applying paint. NEVER paint pilot or around pilot area. WARNING Dust and debris accumulation can result in poor performance. Inspect the Valve compartment, burner parts and log set frequently and Clean these parts monthly or as often as accumulation warrants. 20 20004555 Radiance Vent-Free Gas Heater Catalytic Combustor The combustor should be cleaned annually to ensure optimal performance. Follow the procedure below. Remove the Combustor Module 1. Be sure the heater is COLD. 2. Remove the front plate, top grille and screen. (Fig. 36) 3. Use the phillips screwdriver to remove the two sheet metal screws that secure the combustor to the top of the firebox. (Fig. 37) Use a flat screwdrive to lift the unit up and out through the front of the stove. Clean the Combustor Module 1. Clean the outer surface of the filter with the brush atST139 Fig. 36 Remove the front plate and top grille/screen. tachment of your vacuum sweeper to remove loose dirt. 2. Submerge the filter in a mild soapy water solution. Rinse thoroughly with distilled water. 3. Replace in heater when dry. Replace the Combustor Module 1. Slide the combustor through the front opening of the stove and insert it into the housing on top of the firebox. Secure with the two sheet metal screws. 2. Replace the glass panel and front. ST201 Fig. 37 Remove the catalytic combustor module. 20004555 21 22 Radiance Vent-Free Gas Heater 20004555 PILOT ON OFF PILOT ADJ LO HI 1a 1b 1c 2 4 6 7 13 3 4555.. RUVSOD PARTS 7/24/01 djt 23 8 16 17 18 5 10a,b 21 19 9 20 24a,b, c,d 11a 11b 15 25 27 28 29 22 12a,b 14 30 4555 CFM Specialty Home Products reserves the rig...
Otros modelos de este manual:Eléctrico - 3358 (979.32 kb)
Eléctrico - 3370 (979.32 kb)
Eléctrico - RUVSOD: 3357 (979.32 kb)