Votos - 4, Puntuación media: 3.3
(
)
)
|
Resumen del manual
Nine Eighteen Freeburg Ave. Belleville, Illinois 62222-0529 16009-1-0504 PARTS LIST PARTS LIST SR-18T SR-30T PLEASE NOTE: When ordering parts, it is very important that part number and description of part coincide. INDEX PART INDEX PART NUMBER NUMBER DESCRIPTION NUMBER NUMBER DESCRIPTION 1 13348 CASING SIDE ASSEMBLY - LEFT 1 13348 CASING SIDE ASSEMBLY - LEFT 2 SR-090 CASING BACK 2 SR-041 CASING BACK 3 R-2313 PIEZO IGNITOR 3 R-2313 PIEZO IGNITOR 4 SR-008 CASING SIDE ASSEMBLY - RIGHT 4 SR-008 CASING SIDE ASSEMBLY - RIGHT 5 SR-113 VALVE BRACKET 5 SR-113 VALVE BRACKET 6 R-6563 GAS VALVE -SIT 6 R-6563 GAS VALVE -SIT 7 R-2330 BURNER 7 R-2329 BURNER 8 SR-119 ORIFICE SHIELD 8 SR-114 ORIFICE SHIELD 9 SR-032 PILOT BRACKET 9 SR-032 PILOT BRACKET 10 R-6307 PILOT ASSEMBLY (NAT ONLY)) 10 R-6307 PILOT ASSEMBLY (NAT ONLY)) (INCLUDES ITEMS 11 & 12) (INCLUDES ITEMS 11 & 12) 10 R-6308 PILOT ASSEMBLY (LPG ONLY)) 10 R-6308 PILOT ASSEMBLY (LPG ONLY)) (INCLUDES ITEMS 11 & 12) (INCLUDES ITEMS 11 & 12) 11 R-6310 PILOT THERMOCOUPLE 11 R-6310 PILOT THERMOCOUPLE 12 R-6309 SPARK IGNITOR 12 R-6309 SPARK IGNITOR 13 R-2315 MAIN BURNER ORIFICE - NAT (3 13 R-2315 MAIN BURNER ORIFICE - NAT (5 REQUIRED) REQUIRED) 13 R-2498 MAIN BURNER ORIFICE - LPG (3 13 R-2498 MAIN BURNER ORIFICE - LPG (5 REQUIRED) REQUIRED) 14 R-2314 ORIFICE HOLDER (3 REQUIRED) 14 R-2314 ORIFICE HOLDER (5 REQUIRED) 15 SR-204 TUBING - MANIFOLD TO BURNER 15 SR-203 TUBING - MANIFOLD TO BURNER TWO THREE 16 SR-201 TUBING - MANIFOLD TO BURNER 16 SR-202 TUBING - MANIFOLD TO BURNER ONE AND THREE (2 REQUIRED) ONE AND FIVE (2 REQUIRED) 17 SR-098 TUBING - GAS VALVE TO PILOT 17 SR-201 TUBING - MANIFOLD TO BURNER 18 R-2334 MANIFOLD TWO AND FOUR (2 REQUIRED) 19 R-5097 INLET REGULATOR - NAT 18 R-2333 MANIFOLD 19 R-5098 INLET REGULATOR - LPG 19 12437 TUBING - INLET REGULATOR TO 20 10753 INLET REGULATOR BRACKET GAS VALVE 21 12439 TUBING - GAS VALVE TO MANIFOLD 20 12440 TUBING - GAS VALVE TO MANIFOLD 22 12437 TUBING - INLET REGULATOR TO 21 10753 INLET REGULATOR BRACKET GAS VALVE 22 R-5097 INLET REGULATOR - NAT 23 R-2304 CHROME GRILL 22 R-5098 INLET REGULATOR - LPG 24 SR-076 CASING LOUVER (2 REQUIRED) 23 SR-054 TUBING - GAS VALVE TO PILOT 25 SR-070 REFLECTOR ASSEMBLY 24 R-2303 CHROME GRILL 26 SR-077 HEAT SHIELD 25 SR-017 CASING LOUVER (2 REQUIRED) 27 R-1992 BULB CLIP 26 SR-009 REFLECTOR ASSEMBLY 28 SR-120 OPTIONAL SRS-18 FLOOR STAND 27 SR-018 HEAT SHIELD KIT 28 R-1992 BULB CLIP 29 SR-122 OPTIONAL SRB-18T BLOWER KIT 29 SR-115 OPTIONAL SRS-30 FLOOR STAND (INCLUDES 30 THROUGH 37) KIT 30 R-1454 BRASS BUSHING (4 REQUIRED) 30 SR-116 OPTIONAL SRB-30T BLOWER KIT 31 R-1499 RUBBER GROMMET (4 REQUIRED) (INCLUDES 31 THROUGH 38) 32 SR-196 BLOWER PAN 31 R-1454 BRASS BUSHING (4 REQUIRED) 33 R-2099 CORD SET ASSEMBLY 32 R-1499 RUBBER GROMMET (4 REQUIRED) 34 R-1468 BUSHING - HEYCO #SR5KN4 33 SR-198 BLOWER PAN 35 R-2395 WIRE ASSEMBLY 34 R-2099 CORD SET ASSEMBLY 36 R-2503 FAN CONTROL 35 R-1468 BUSHING - HEYCO #SR5KN4 37 R-2396 BLOWER (INCLUDES MOTOR, FAN, 36 R-2395 WIRE ASSEMBLY AND FAN HOUSING) 37 R-2503 FAN CONTROL NS SR-219 BLOWER HARDWARE PACKAGE 38 R-2396 BLOWER (INCLUDES MOTOR, FAN, NS R-2390 IGNITOR WIRE AND FAN HOUSING) NS SR-216 HARDWARE PACKAGE NS SR-219 BLOWER HARDWARE PACKAGE NS R-2390 IGNITOR WIRE NS SR-216 HARDWARE PACKAGE USE ONLY MANUFACTURED REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR DEATH. 16009-1-0504 Page 17 PARTS VIEW PARTS VIEW SR-10T Page 18 16009-1-0504 PARTS VIEW PARTS VIEW SR-18T 16009-1-0504 Page 19 Page 20 16009-1-0504 SR-30T PARTS VIEW OPTIONAL BLOWER INSTALLATION ISNTRUCTIONS OPTIONAL BLOWER INSTALLATION ISNTRUCTIONS SRB-18T and SRB-30T for Unvented Room Heaters SR-18T and SR-30T INSTALLING OPTIONAL BLOWER SRB-18T OR SRB-30T If heater is installed onto the wall, in order to install the optional blower, the heater must be removed from the wall. If heater is installed on optional floor stand there is adequate access area available to install the optional blower. 1. Turn "OFF" gas supply to the heater. 2. Remove lower louver from casing assembly (2 screws). 3. Remove reflector from casing assembly (2 screws). 4. Remove upper louver from casing assembly (2 screws). 5. Insert the fan control wires and the upper portion of the fan control through the 3/4" (19mm) diameter hole on the bottom side of the top heat shield. The fan control wires will enter into the top portion of the heater and the fan control disc will be facing the ceramic plaques. Attach fan control to the bottom side of the top heat shield with (2) screws provided with the optional blower. 6. Route cord set through 9/16" (14mm) diameter hole on casing assembly back. Insert approximately 3" (76mm) of cord set into casing assembly back. 7. When you are facing the front of the heater, position the optional blower assembly onto the top heat shield of the heater. The motor wire harness should be facing into the top, right portion of the heater. 8. Attach (1) pin terminal from black (hot) wire, smooth insulat...
Otros modelos de este manual:Eléctrico - SR-18T-3 (995.63 kb)
Eléctrico - SR-30T-3 (995.63 kb)