Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
Remedy: Re-examine the area to be heated and the calculated heat loss. The furnace may be too small for the house. The furnace could be working perfectly but the demand is too great. That's the reason why we build different size furnaces. Remedy, get a larger furnace, or lower the heat loss of the home. 33. Unit is oversized for the area to be heated. Remedy: Replace with a smaller unit, or provide more air distribution to other rooms. 34. Not enough pellets placed in firepot on start-up to bring the furnace up to lock in temperature on the safety disc. Remedy: Stop operation, let the unit cool (never place pellets by hand into a hot firepot), and re-light with more (2-3 cups) pellets in the firepot. 35. Door or glass seal worn or broken. Remedy: Replace with new gasket. 36. Draft inducer motor defective. Remedy: Remove inducer motor from housing and connect to direct power, if non- functioning, replace with new motor. 37. Flue vent outlet blocked. Remedy: Check piping and outlet to verify clear passage. 38. Summer (white) fan button pushed in on fan limit control. Remedy: Pull button back out to auto position. 39. Air shutter on draft inducer too far open. Remedy: Close down air shutter to 50%. 40. Air shutter on draft inducer too far closed. Remedy: Open air shutter up to 50%. 41. Dust present due to carelessness when loading the stove. Remedy: Take your time when loading pellets into hopper. 42. Unit has run out of fuel. Remedy: Load hopper. 43. Undersized or overloaded service wiring. Remedy: Call your electrical contractor. 44. Power surge. Remedy: Call your electrical contractor. 45. Power short in unit. Remedy: Locate short circuit and correct. 46. Pellets in hopper are giving off an odor. Remedy: Change the brand of pellets you are using, some species of wood have unpleasant odors. 47. Mounting bolts on the blower are loose. Remedy: Tighten the mounting bolts. 48. Remote thermostat is not level. Remedy: Level the thermostat using a water bulb. 49. Ash pan door or other heat exchanger cover plate not on tight. Remedy: Tighten all nuts and check all gaskets. 50. Thermostat wires are shorting out. Remedy: Remove thermostat from the base, if burner continues to run, go back to tie in at primary control yellow leads, disconnect and separate, if burner stops, then you have a short in the remote wires. Trace and correct or replace. Look for tacks or nails through wires. 51. A bearing is failing on the blower motor. Remedy: Replace the blower. 52. Fan limit control is stuck. Remedy: Make sure that the white button is in the auto position, tap the fan limit control lightly. If this does not shut of the blower then replace the fan limit control. 53. Bad pellets. Remedy: Are you using approved pellets that meet the manufacturer's specifications? Use of non approved pellets will impair the functioning of your stove and may void your warranty. 54. That's the nature of the Honeywell T87F thermostat. Remedy: Adjust thermostat to your comfort level not a numbered dial. 55. Normal draft inducer hum anytime the unit is plugged in. Remedy: Install duro-dyne duct isolator. 56. Blower blades are dirty and full of lint and/or hair. Remedy: Clean the blades. 57. Draft inducer blades are dirty and full of lint and/or hair. Remedy: Clean the blades. 58. Furnace venting improperly installed. Remedy: Check installation manual to verify correct install on unit. 59. Aluminum air filter is dirty. Remedy: Remove from furnace and wash. 60. Inadequate return air. Too small, restricted, or is pulling unconditioned air. Remedy: Consult qualified HVAC ducting contractor for proper installation. PARTS LIST 1. Hopper connector flange F000221P 8. Cup motor F000101P 2. Pillow block ball bearing F000505P 9. Manual reset F000105P 3. Cutting blades (2) ea. F070513P-2 10. Auger motor F000102P 4. Fuel metering cup F070512P 11. Draft inducer F000103A 5. .” lovejoy coupling F000507P * 12. Auger/shaft assembly F070910P 6. Spider F000505P 13A. Fire pot (complete) ** F070954A (corn) 7. .” lovejoy coupling F000507P * 13B. Cast pot liner ** F062700P (corn) 13C. Pellet pot F070903S (pellet) * Durham or Dayton brand auger motors use 3/8” coupler. Merkle-Korff brand auger motor uses .” coupler. ** Corn pots are 2 piece units consisting of a stainless steel holder with a removable cast iron liner. Text Box: WARRANTY NON TRANSFERABLE MODEL: _GBU070___________ SERIAL NUMBER: ____________________ DATE PURCHASED: __________________ FROM: __________________________ Complete Unit Warranty The manufacturer provides a warranty on all steel parts (except burn pot) and electrical components against defects in material or workmanship under normal use and maintenance for a period of one (1) year from the installation date. There is expressly no warranty on the following components: burn pots, fibreglass rope gasket, paint, or gaskets. This warranty covers defects in materials and workmanship in covered components, provided the product has been installed and operated...
Otros modelos de este manual:Eléctrico - GBU070 (231.86 kb)
Eléctrico - GBU070 (231.86 kb)
Eléctrico - GBU070 (231.86 kb)
Eléctrico - GBU070 (231.86 kb)