Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
KEEP THIS NUMBER FOR FUTURE REFERENCE. Bionaire® and Bionaire® Logo are registered trademarks of The Holmes Group, Inc. SmartTouch™ is a trademark of The Holmes Group, Inc. HEATER SERVICE INSTRUCTIONS 1. Do NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void the warranty. The inside of the unit contains no user serviceable parts. All servicing should be performed by qualified personnel only. 2. If you need to exchange the unit, please return it in its original carton, with a sales receipt, to the store where you purchased it. If you are returning the unit more than 30 days after the date of purchase, please see the enclosed warranty. 3. For service information please call 1-800-788-5350 or visit our website at 4. • If you have any other questions or comments, feel free to write to us: The Holmes Group, Inc. Consumer Service Department 32B Spur Drive El Paso, TX 79906 than the rating of the heater. Care must be taken to arrange the extension cord where it cannot be pulled on by children or accidentally tripped over. AUTO SHUT-OFF To prevent damage and risks due to overheating this unit is equipped with a built-in overheat, protection device. It cuts off the power as soon as the heater’s internal temperature becomes too hot. This patented, technologically advanced system requires the user to reset the heater if there is a potential overheat situation. It will only resume operation when the user resets it. To Reset the Heater: 1. Unplug the heater and wait 10 minutes for the unit to cool down. 2. After the 10 minutes, plug the unit in again and operate normally. 3. Push power button on, set Mode to desired setting. PRE-OPERATING INSTRUCTIONS Carefully unpack your heater from the box (it is recommended to save the box for off-season storage). OPERATING INSTRUCTIONS Heat Control 1. Place the unit on a firm level surface. Plug in the heater to a 120V power source. 2. To start the unit, press the mode button. The POWER light will remain lit while the heater is in operation. Fig. 1 Exhaust Panel Air Intake Oscillation Base (BFH3416 only) SMARTTOUCH™ THERMOSTAT INSTRUCTIONS To take advantage of the SmartTouch™ Thermostat continue to press the MODE/OFF button until the desired temperature is set in either the HIGH (1500 Watt) or LOW (750 Watt) setting. When ambient temperature rises above the set temperature, the heater will stop. When the ambient temperature drops below the set temperature, the heater will turn on automatically. Note: When the SmartTouch™ thermostat is set, either the HIGH or LOW power light, and the set temperature light will remain lit during operation. Note: It is normal for the heater to cycle ON and OFF as it maintains the preset temperature. To prevent the unit from cycling, you need to raise the thermostat setting. Note: SmartTouch™ has memory. The SmartTouch™ thermostat will remember the previous temperature setting after the unit has been turned off. However, if the unit is unplugged, the SmartTouch™ thermostat will be reset and will no longer remember the previous temperature setting. REMOTE CONTROL OPERATION 1. Before operation, insert 2 AAA batteries into the back of the remote control. • Do not mix old and new batteries. • Do not mix alkaline, standard (carbon-zine), or rechargeable (nickel-cadmium) batteries. 2. Press the power button ( ) on the remote control to begin operation. Press the button a second time to turn the heater off. 3. To change the heat or thermostat settings, press the mode button. The mode button will scroll through the two heat settings, then switch into Auto mode so that the thermostat can be adjusted. Once in Auto mode, continue to press the mode button until the desired temperature setting is reached. OSCILLATION (BFH3416 ONLY) For maximum heat distribution use the oscillation function. 1. Press the Oscillation button on the remote control to begin 90° oscillation. 2. To stop the heater from oscillating, press the Oscillation button a second time; the unit will stop in that direction. To resume oscillation, press the Oscillation button again. Note: The oscillation feature can only be operated from the Remote Control. DO NOT attempt to turn oscillation by hand. Severe damage to the mechanism could result. MAINTENANCE INSTRUCTIONS During Season Care Before cleaning make sure the unit is unplugged. 1. Allow the heater to cool before cleaning. 2. Carefully wipe the unit with a soft, damp cloth. 3. Please be cautious near the heating elements. . TIP: Over time, dust may accumulate on the front grills. This can be removed by wiping the unit with a damp cloth. Always unplug unit and allow to cool prior to cleaning. After Season Care Store heater in a cool, dry location. Bionaire® recommends storing the unit in its original, or appropriately sized, box. TROUBLESHOOTING . If your heater fails to operate: . Make sure the electrical outlet or circuit breaker is working. . Check for obstructions. If you ...
Otros modelos de este manual:Eléctrico - BFH3414 (86.08 kb)