Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
Tighten securely. *** IMPORTANT NOTE: be sure to route and keep the electrical cord AWAY from the main body of the heater unit. *** FigT3 Min. Clearances: 83” head unit height 10” from mounting wall 12” from surfaces above the heater head unit 36” from sides and front of head unit 45-55 degree angle of operational spread Route power cord below and away from head unit as show in box 5. ///?*?*//. Correct v/ ///?*’// Wrong Wrong to lock position of head unit. Page 5 *** Important Notice *** Do not return to place of purchase!! Please contact our Toll Free Hotline: (866) 985-7877 for customer service & warranty issues Operating Instructions This appliance MUST be grounded. * When using outdoors, we recommend using a certified GFI (Ground Fault Interrupt) outlet to protect against electrical shock. * Ensure that the heater mounting bracket is SECURELY fastened to the wall, patio overhang or house eave. * Route electrical cable AWAY from main body of heater which gets very hot. * Do NOT cover or obstruct the main body of the heater during use. * All Installations must be in accordance with I.E.E. safety regulations or equivalent. If you are unsure, consult an electrical service professional. * Avoid the use of an extension cord with this appliance. If one is used, it MUST be at least a 14/3 wire, grounded cord, 50ft max. length. * Do not place any objects such as furniture, papers, clothing or curtains closer than 3 ft to the front and sides of the heater. NOTE: your IR Heater main body, electrical components & bracket comes fully factory assembled. Do NOT attempt repair or disassembly, contact our toll free customer service hotline for assistance. A CAUTION L- For optimal performance and safety concerns, we HIGHLY RECOMMEND that the Infrared Heater Head be operated at a mill, of 84” ht. with a 45-55 degree angle of operational spread. To Adjust The IR Head Unit: Swivel head unit up or down to desired position. The head unit must be at a 45-55 degree angle for optimal operation and output. There should only be a moderate amount of tension to maintain the swivel bracket. If it becomes too loose, tighten hex nuts and bolts at swivel points on head unit bracket. Note: Be sure electrical cord is routed and positioned away from head unit. Step 1 Before turning on your Infrared Heating System, adjust the head unit angle as desired. Do NOT touch the head unit during operation or for 30 minutes AFTER shut off. The head units GETS VERY HOT! Refer to coverage area in Fig. 7 for best positioning location and heat spread/coverage. Step 2 The infrared electric heating system comes equipped with a heavy duty 16/3 gauge wire and grounded plug. This appliance must be used with an outlet that has been installed and grounded in accordance with all local codes and ordinances. Make sure that the heater is connected to an outlet having the same configuration as the plug shown in Fig. 8. Do NOT use an adapter with this product. Check with a licensed electrician if the grounding instructions are not understood completely or if the wall outlet does not match the plug. Step 3 Always UNPLUG unit when not in use! Your Mojave Sun, infrared electric heating system is ready to enjoy. Plug the appliance in and beginning enjoying the warmth! A WARNING! 5 Page 6 *** Important Notice *** Do not return to place of purchase!! Please contact our Toll Free Hotline: (866) 985-7877 for customer service & warranty issues Maintenance & Storage Specifications Model: Voltage: Amps: Wattage: Lamp Type: Min. Operational Height: Weight; Head Unit Dimensions: MS-1500WOIRPH-WM 120 volts 12.5 amps 1500 watts Quartz Halogen 84” (7 ft.) 5.5 lbs. 4.5” x 7” x 22” Storage Always UNPLUG unit when not in use! * The IR Head unit can be left outside during the season as long as it is mounted under a covered, protected location. - During expected moderate weather conditions, we recommend wrapping the head unit with a poly bag and tape or a bungee cord. For extreme weather conditions, it is recommended that you remove the unit from the wall bracket and store in a safe, dry indoor location. * When not in use for extended periods of time, the IR Head Unit can be easily removed from the wall mounting bracket for storage indoors. Refer to step 3, page 5 of this manual. - The halogen lamp is fragile, be careful not to hit or jar the head unit. - Store in a dry location placing the head unit on a soft cushioned surface. - Make sure the electrical cord is properly coiled and out of the way. Maintenance Your infrared heating system is virtually maintenance free! A few minutes to wipe down exposed surfaces is all it takes. * Head Unit & Aluminum Shield - Use any non-abrasive cleaner and soft cloth to wipe off debris and dirt from the exposed surfaces of the aluminum shield and outer body of the head unit and outer grill. NEVER spray any liquids or cleaners into the housing area where the halogen lamp i...
Otros modelos de este manual:Eléctrico - 02110 (7.02 mb)
Eléctrico - MS-1500WOIRPH-WM (7.02 mb)