Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
Disconnected cylinders must have threaded valve plugs tightly installed, and must not be stored in a building, garage or any other enclosed area. -4- ASSEMBLY 1. 3 pcs castle nuts 2. Reflector 3. 6 pcs 8mm washers for pins support 4. 3 pcs 90mm (L) pins for reflector support 5. Head assembly 6. 4 pcs M6xl0mm bolts 7. 2 pcs Post assembly 8. Tank housing 9. Regulator 10. 6 pcs M6x30mm bolts and 6mm nuts for connection of post support and support legs 11. 3 pcs M8xl6mm bolts for connection of support legs and base 12. Post support 13.6pcs M6xl2mm bolts for connection of LPG cylinder fixed parts with base 14. 3 pcs. Support legs 15. Base 16. 1 pcs open end wrench (10&13mm) -5- ASSEMBLY WARNING: This appliance requires installation by a competent person. Proper assembly is the responsibility of the installer. Step 1 1-1. Attach 3pcs LPG cylinder fixed parts on the base with 6pcs M6x12mm bolts. 1-2. Position the 3 pcs support legs on the base as shown in the picture to the right. 1-3. Use 3 pcs M8x16mm bolts to affix the support legs to the base. Step 2 2-1. Put the post support on top of the 3 pcs support legs. 2-2. Use 6pcs M6x30mm bolts and 6mm nuts to connect the post support and support legs. 2-3. Use 4 pcs. M6X10mm bolts to connect the first piece of the post assembly to the post support. F\ -6- ASSEMBLY Step 3 3-1. Connect the second piece of the post assembly to the first piece of the post assembly and screw on clockwise. Step 4 4-1. Place the tank cover on the base. Step 5 5-1. Secure the 3 pcs 90mm pins(reflector support bolts) on the cap of emitter screen. 5-2. Route the gas hose up through the post and out of the top. 5-3. Connect the gas hose to the gas burner inlet connector. 5-4. Fix the head unit collar to the post with 4 pcs M6xl0mm bolts. r\ 3 I - I I p -7- ASSEMBLY Step 6 6-1. Put 8mm washer on each reflector support bolt. 6-2. Fasten the reflector with 3 pcs washers and 3 pcs M8 mm castle nuts. Step 7 7-1. Lift the tank cover and the post flange. 7-2. Connect the other end with regulator to the ge tighten. Warning: When connecting the gas cylinder and regulator, make sure the connection is tight and always check for any leaks. Please see page 9 "Check for Leak" for full instructions. 7-3. Put gas cylinder on the stand. rest it on of gas hose as cylinder and Ln ASSEMBLY 7-4. Lower tank over gas cylinder and down to cover base. Check for Leak Your patio heater has been checked at all factory connections for leaks, but you should always check when you attach the LPG cylinder. To check for leaks, follow these instructions: --Assemble all gas connections; --Connect regulator assembly to the propane tank; --Make sure the heater valve is turned OFF. 1) Make soapy solution by mixing 1 part liquid dish soap and 3 parts water. 2) Open the propane tank valve. 3) Spoon several drops (or use squirt bottle) of the soapy solution onto the gas hose /regulator and regulator/cylinder connection. 4) Inspect the connections and look for bubbles. 5) If no bubbles appear the connection is safe. 6) If bubble appears, there is leakage. Close the propane tank valve, and loosen and re-tighten this connection. 7) Check for leakage again. -9- ASSEMBLY 8) If bubbles still appear, close the propane tank valve and contact your gas supplier. If a leak is detected, DO NOT attempt to use the heater. MAKE SURE to check all THREE connections between the cylinder and gas line. NOTE: 1)The cylinder must be provided with a shut off valve terminating in a LPG supply cylinder valve outlet specified, as applicable, for connection NO 510 in the standard for compressed gas cylinder valve outlet and inlet connections, ANSI/CGA-v-1. 2) The cylinder supply system must be arranged for vapor withdrawal. 3) The cylinder used must include a collar to protect the cylinder valve. Annually check operation: A. Lift the tank housing up above the LPG cylinder and rest it on the support leg assembly. B. Open the propane tank valve. -10- ASSEMBLY C. Spoon several drops(or use squirt bottle)of the solution onto gas hose connection and pilot connection. D. Inspect the connections and look for bubbles. E. If no bubbles appear, the connection is safe. F. If bubbles appear, there is a leak. Close the propane tank valve and loosen and re-tighten this connection. G. Check for leaks again. H. If bubbles still appear, close the propane tank valve and call the gas supplier. DO NOT attempt to use the heater. OPERATION WARNING: DO NOT attempt to operate heater until you have read and understand all precautions. Failure to do so can result in serious personal injury, death or property damage. Before Turning Gas Supply ON. Your heater was designed and approved for OUTDOOR USE ONLY. DO NOT use it inside a building or any other enclosed area. Make sure surrounding areas are free of combustible materials such as gasoline and other flammable vapors or liquids. E...
Otros modelos de este manual:Eléctrico - FireSense 60763 (4.65 mb)
Eléctrico - PH01-S (4.65 mb)