Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
The first tacitly approved working mode of the system is the solar heating mode. The four-number tube of the indication screen displays the clock. The five- number tube under the screen respectively displays water temperature of water-storing tank and the temperature of water exiting. The indication interface is displayed in Fig. 6 and at this time, all the pressing keys are effective. Then press power supply key and the system will be turned off and enter the electricity saving mode. The indication interface is displayed in To ensure that customers can use water heater properly and safely, we here seriously inform our customers that you must contact the appointed professional serving personnel for installing and service. For any improper installment, our company will not burden any responsibility. When the power supply is connected, the pump is electrified;Pay attention that connecting lines of pump are inserted stably, and can not load emptily. Before any maintenance and repair of water heater, please make sure that you cut off other power Supply. Non-professional persons are not allowed to adjust and maintain water supply. Before electrification please make sure that machines are full with water, otherwise it will cause a system malfunction. Please make sure that the sockets are subject to national standards and are connected to the ground reliably. It is prohibited to use water heater without a reliable grounding. The water heater is equipped with safety valves. for secure use, please do not change installment position personally. The evacuating tube nozzle should be downwards vertically and are open to the air so as to prohibit jamming the exit. A draining pipe is linked to the evacuating tube nozzle and leads to the sewer opening. (the draining pipe is otherwise sold) Hot water with a temperature higher than 50 might result in scalding and customers should mix hot water and cold water and then have a shower or wash. In cases when water heater is seriously soaked, it must be checked by technical personnel ratified by our company before it is reused. The hot water in water heater is not suitable for drinking. As a result of long- term use, scale might be produced in the water tank. Meanwhile, the aging of the water pipe can result in a change of water quality. Therefore, when you wash rice and vegetables with water in the container, please wash them once again with clean tap water. When collector equipment is installed, it can not be inversely placed. Outdoor pipeline must use metal pipes. Heat-preserving of pipelines must use specially designed materials by our company. Collector equipment should be installed facing south. Evacuating opening of the system safety valve should be connected to the release opening of sewage. All parts of the whole system are not allowed to be disconnected personally otherwise, results should be burdened personally. 411 Attentions in installment Installation Use method Attentions in installment Installation Use method Electric controller should be far from strong interfering sources. Tne-way pipeline between water-storing tank and collector equipment must be less than 10 meters. Sensor of collector equipment should be installed at the water exiting Opening. The exhaust valve should be installed vertically at the water exiting opening of collector equipment and its position in the pipeline should be kept the highest. To screw loosely the exhaust cap after installment to make it exhaust freely. Pay attention the crossing corner of water entering and exiting opening should be connected and the bottom one is for water-entering and the top one is for water exiting in the installment of collector equipment with flat board. Installment of solar water heater is composed by the following parts: installment of collector equipment, installment of water-storing tank and installment of water pump. Installment of each part should be completed by the professional installing personnel appointed by our company in order to ensure good functioning of the system. Installment of collector equipment Collector equipment of solar water heater is installed with the method of oblique top. collector equipment is placed on the southern rooftop of the house so as to ensure that the equipment faces south and there is no shelter ahead. All the four corners of each collector equipment are linked perfectly with steel wire rope. the other end of the steel wire rope is fixed under eaves or on the wallwith a expanding bolt. Pay attention that the steel wire rope is strained and the expanding bolt is beaten firmly. Take the installment of solar water heater of BRF1-120/150W as an example. For the sketch map of installment, please see Fig.3. Collector Steel wire rope Expanding bolt Fig.3 Installment sketch map of BRF1-120/150W storage. in cases when the machine is turned on, press the mode key to enter the solar energy heating mode (Note: the first time the system is electrified, this mode can be entered). The ...
Otros modelos de este manual:Eléctrico - BRF1- 150W (767.74 kb)
Eléctrico - BRF1- 120 (767.74 kb)
Eléctrico - PJF1- 150W (767.74 kb)