Votos - 4, Puntuación media: 4.3 ( )

Fabricar: Cadet Tamaño del archivo: 3.48 mb Nombre del archivo: Idioma del manual:

3. Undernocircumstancesshouldthisappliancebeoperatedwithout the glass front or with a broken glass front. Replacement of the glass (with gasket) as supplied by the manufacturer should be done by a qualified service person. 4. Do not abuse the glass by striking or hitting the glass. WARNING: Do not use abrasive cleaners on glass. Do not attempt to clean glass when glass is hot. It is not unusual for your gas fireplace to give off some odor the first time it is burned. This is due to the curing of the paint and any undetected oil from the manufacturing process. Please ensure that your room is well ventilated -open all windows. It is recommended that you burn your fireplace for at least six (6) hours the first time you use it. If optional fan kit has been installed, place fan in the “OFF” position during this time. IMPORTANT: Turn off gas before servicing appliance. It is recommended that a qualified service person perform these checkups at the beginning of each heating season. • Clean Burner and Control Compartment Keepthecontrolcompartment,logs,andburnerareassurrounding the logs clean by vacuuming or brushing at least twice a year. Cleaning Procedure 1. Turn off pilot light at gas valve. 2. Remove glass front. (See Glass Removal) 3. Vacuum burner compartment. 4. Reinstall glass front. 5. Ignite pilot. (See Lighting Instructions) 6. Operate the pilot burner. If it appears abnormal call a service person. • Check Vent System The appliance and venting system should be inspected before initial use and at least annually by a qualified service person. Inspect the external vent cap on a regular basis to make sure that no debris is interfering with the air flow. Glass Cleaning It will be necessary to clean the glass periodically. During start-up condensation, which is normal, forms on the inside of the glass and causes lint, dust and other airborne particles to cling to the glass surface. Also initial paint curing may deposit a slight film on the glass. It is therefore recommended that the glass be cleaned two or three times with a non-abrasive household cleaner and warm water (we recommend gas fireplace glass cleaner). After that the glass should be cleaned two or three times during each heating season depending on the circumstances present. General Glass Information Glass Removal and Replacement (Figure 64) 1. Remove top louver, grasp louver and pull forward. 2. Lower bottom louver. 3. Release two glass frame clamps at bottom of firebox. 4. Remove glass frame. 5. Place glass frame onto firebox. 6. Attach two glass frame clamps at bottom of firebox. 7. Align clips on top louver with slots on front posts. Replace top louver into fireplace. 8. Close bottom louver. Figure 64 WARNING: Do not operate appliance with the glass front removed,crackedorbroken.Replacementoftheglassshould be done by a licensed or qualified service person. Only glass approved for use by the manufacturer in fireplace may Louver Removal and Installation be used for replacement. The glass replacement should be done by 1. Remove top louver, grasp louver and pull forward. a licensed or qualified service person. 2. Lower bottom louver. 3. Align clips on top louver with slots on front posts. Replace WARNING: top louver into fireplace. 1. The use of substitute glass will void all product warranties. 4. Close bottom louver. 2. Care must be taken to avoid breakage of the glass. Page 48 23552-4-0408 PARTS LIST INDEX NO. PART NUMBER DESCRIPTION DVD32 DVD36 DVD42 DVD48 1 R-7654 R-7654 R-7654 R-7654 FLUE INSULATION 2 17425 17425 17425 17425 FLUE INSULATION RETAINER 3 R-7566 R-7566 R-7566 R-7566 INLET VENT ADAPTOR 4 R-7573 R-7573 R-7573 R-7573 INLET VENT GASKET 5 17155 17155 17155 17155 FLUE OUTLET ASSEMBLY 6 M163 M163 M163 M163 FLUE CONNECTOR GASKET 7 17142 17142 17142 17142 VENT COVER PLATE 8 R-7575 R-7575 R-7575 R-7575 VENT COVER PLATE GASKET 9 17141 17141 17141 17141 FLUE COVER PLATE 10 R-7574 R-7574 R-7574 R-7574 FLUE OUTLET GASKET 11 17301 17149 17149 17149 TOP STANDOFF (2 required) 12 17317 17317 17319 17320 TOP SHIELD 13 10554 10554 10554 10554 NAILING FLANGE (4 required) 14 17162 17162 17162 17162 JUNCTION BOX ASSEMBLY 15 R-3492 R-3492 R-3492 R-3492 RECEPTICAL, 3-PRONG 16 17169 17127 17187 17210 LOUVER ASSEMBLY-UPPER 17 17172 17134 17190 17213 GLASS DOOR FRAME ASSEMBLY 18 17170 17128 17188 17211 LOUVER ASSEMBLY LOWER 19 17174 17143 17197 17215 BAFFLE, FLUE VENT 20 R-7587 R-7556 R-7598 R-7598 REAR LOG 21 R-7586 R-7555 R-7597 R7597 MIDDLE LOG 22 R-7585 R-7553 R-7553 R-7553 FRONT LEFT LOG 23 N/A N/A R-7601 R-7601 CENTER EMBER 24 R-7554 R-7554 R-7554 R-7554 FRONT RIGHT LOG 25 R-7588 R-7557 N/A N/A "Y" TWIG 26 N/A N/A R-7600 R-7600 TOP LOG - TWIG 27 N/A N/A R-7599 R-7599 FRONT "Y" LOG 28 R-7580 R-7537 R-7695 R-7695 BURNER TUBE 29 17235 17235 21260 21260 LOG LOCATOR BRACKET 30 17185 17158 17208 17208 BURNER BASE PLATE ASSEMBLY 31 R-7624 R-7624 R-7624 R-7624 AIR SHUTTER 32 P-254 P-288 P-286 P-285 ORIFICE (NAT) 32 P-287 P-182 P-208 P-185 ORIFICE (LP) 33 R-757...

Descargar ahora

Introduzca dos números de la imagen: