Votos - 3, Puntuación media: 5 ( )

Fabricar: Roberts Gorden Tamaño del archivo: 5.17 mb Nombre del archivo: Idioma del manual:

/0# 1"( 1 2 ,-. /0# 3 0& 4 567& % 57 1 8 ,-409 *:" ;<" Description Part Number S-Hook 91907302 Tube/Reflector Hanger 03090100 Total Straight Length (both sides) or Length from U-Tube to U-Tube in a Double "U" Layout Typical Expansion Each Side Minimum “X” Length 0’ - 50’ ±1” (3 cm) 12” (31 cm) 51’ - 60’ ±2” (5 cm) 18” (46 cm) 61’ - 80’ ±3” (8 cm) 24” (61 cm) 81’ - 100’ ±4” (10 cm) 30" (76 cm) 101’ - 120’ ±5” (13 cm) 36" (91 cm) 121’ - 140’ ±6” (15 cm) 42" (107 cm) 141’ - 160’ ±7” (18 cm) 48" (122 cm) If the installation requires a shorter suspension length than the minimum listed, the suspension length may be reduced by 6" (16 cm). In this case, tube clamps MUST be used at the two farthest hangers on each side of the burner. See Page 15, Figure 13. SECTION 7: HEATER INSTALLATION 15 FIGURE 13: Linear Heater Assembly Overview 4 . 5 , 6 ,/70 8 ! "# # 9$ : ; # #% # TF-SERIES INSTALLATION, OPERATION AND SERVICE MANUAL FIGURE 14: Linear Heater Layout Overview !"*:*:- !"1(" %:"))=,4!" :=3# (:=3# ( =9>433/ ! =>,# : !=/0#3: =3,0#4:"!: ,>/*:2? !: >3*:2? !: 3>4*:2? : #>#*:2? ! Linear layouts showing one side. Use same measurements for the other side. SECTION 7: HEATER INSTALLATION FIGURE 15: Linear Heater Layout Overview (Continued) : 4>.*:2? ! 9>3*:2? :! :.>3*:2? ! TF-SERIES INSTALLATION, OPERATION AND SERVICE MANUAL 18 Step 7.1 Burner Tube Installation Step 7.2 Burner Installation 9>4@> 33/@3# *: 3/@3 9,@# "%&' *: A "(!-3, (3>4 ) !:0 " : :!:0 B!! ": ( Description Part Number Burner Tube 03051XXX S-Hook 91907302 Tube/Reflector Hanger 03090100 < # & & Description Part Number Bolt 94273914 Lock Washer 96411600 Gasket 02568200 Burner 090XXXXX SECTION 7: HEATER INSTALLATION 19 Step 7.3 Tube Clamp Package Installation Step 7.4 Coupling and Tube Assembly 4 . 5 ,6 ,/70 Description Part Number Tube Clamp Package 01318901 Tube Clamp 01396801 Bolt 97113940 Flat Washer 95211600 Nut 92113900 ' ' = > >? ' @A B@ & $ < $ $ ' & $ < AClose coupling with tab. B Start Slide bar/Coupling Lock onto coupling. CInsert tubes into coupling. D Tighten coupling to join tubes. Description Part Number Coupling 01329600 Slide bar/Coupling Lock 01329700 Tube 91409XXX TF-SERIES INSTALLATION, OPERATION AND SERVICE MANUAL 20 Step 7.4.1 Coupling and Tube Assembly (Continued) Step 7.4.2 Coupling and Tube Assembly (Continued) ## 9" # 9" , C@ % & * & • Repeat Step 7.4 A - D until all tubes are assembled. See Page 20, Section 7.4.2. Tighten slide bar as shown below ,- ,- .!" "0 D-7# ,- .1" "0 Model Minimum Tube Length Per Side TF-120 20’ (6 m) TF-160 20’ (6 m) TF-200 30’ (9 m) TF-250 40’ (12 m) TF-300 50’ (15 m) TF-350 50’ (15 m) TF-380 60’ (18 m) See recommended venting lengths on Page 34, Section 9, when using maximum tube lengths. SECTION 7: HEATER INSTALLATION 21 Step 7.5 Turbulator Installation Step 7.6 Reflector Installation * C"" *: " : !:D" :" ("0D"D E !" :0 *:" 30#> *:" % ( Description Part Number Turbulator Adapter 03051503 Turbulator Section 2.5' 03051504 Tube 91409XXX Turbulator must be installed in the last standard section of tube. Turbulator Installation Model Tube Section TF-120 2nd 10’ Section Each side TF-160 2nd 10’ Section Each side TF-200 3rd 10’ Section Each side TF-250 N/A TF-300 N/A TF-350 N/A TF-380 N/A Model Each Side TF-120 & TF-160 1 - 03051503 4 - 03051504 TF-200 1 - 03051503 2 - 03051504 ; $ %&" Description Part Number Tube/Reflector Hanger 03090100 Burner Tube 03051XXX Reflector 02750303 NOTE:All tube surfaces must be covered by a reflector, except for a U-Tube. TF-SERIES INSTALLATION, OPERATION AND SERVICE MANUAL 22 Step 7.6.1 Reflector, U-Clip and Reflector Support Installation The pictorial drawings of the heater construction in Section 7 are schematic only and provide a general guideline of where hangers, reflector supports and U-clips are to be installed. To ensure proper expansion and contraction movement of the reflectors, a combination of U-clips and reflector supports are used. The positioning of reflector supports and U-clips depends on the individual installation. Use either pop rivets or sheet metal screws instead of u-clips when installing end caps and joint pieces in areas where impact and high wind may be a factor. The following rules must be observed. 30*D"(! !" *!ED) !"F " (D"(0%" ( D"( D :) G 0 :!"") 0 ;!"(( 0 :0 !"(( " !" D"(0 ,0* !"D"(A 0*!! '!" H" (D"( G 0 !"(( 0 :0 !:!"") EH" ( " ): 0 * !!"F :!! ' : "!"(( 0 !" ? 1( IH1" ( 0*! !"!::!! ' "!!" !"(( 0 !" 4 4 BD"(: !440 2 " -4 3"" " ((0 ( " (BD"( !" (( () " (BD"( !" * *) ;H" (BD"( IH1" ( 3" (( H" (D"( !" * ;H" (BD"( !"(( ( * " Description Part Number Reflector Support Package 03050010 Wire Form 91908004 Reflector Support Strap 03050000 Screw #8 x 3/4 94320812 U-Clip P...

Descargar ahora

Introduzca dos números de la imagen: