Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
This is quite normal – the fumes are non-toxic and will quickly disappear. We recommend that you open a window to ventilate the room when using the heater for the first time. Controls Thermostat -see Fig. 3 The thermostat controls the heat output according to the room temperature. Fig. 3 This ensures that the heater will not produce heat unnecessarily when the room is warm. To set the temperature you require, turn the thermostat knob clockwise until the desired temperature is reached. Alternatively to heat a cold room quickly, turn the thermostat knob up fully. When the room has reached the desired temperature, turn the thermostat knob anti-clockwise until the thermostat just clicks off. The heater will now automatically operate at this temperature. The thermostat also has a frost protection setting marked ‘*’. This setting is useful in areas such as garages to prevent frost damage. If the thermostat is set to its minimum setting ‘*’, the heater will cycle ON and OFF to maintain a temperature of approximately 5°C to help protect against frosty conditions. Digital Timer Operation - see Fig. 4 IMPORTANT: Remember to observe all safety warnings when operating the heater on auto setting, either attended or unattended. The timer allows you to select ‘AUTO’ or ‘MAN ON’ by pressing the ‘MODE’ button until the required MODE appears at the bottom of the timer display. ‘AUTO’ MODE allows the heater to switch ON and OFF according to a set 24 Hour program period (see ‘Setting Programs’ section below). ‘MAN ON’ MODE allows power to the heater uninterrupted by the program settings. Key Lock: If ‘ENTER’ and ‘MODE’ are pressed within 1 second, the keys will be locked. The user will know the keys are locked as the lock symbol ‘ ’ will be displayed on the top left hand corner of the screen. To unlock the keypad, press ‘ENTER’ and then ‘MODE’ within 1 second. Initial Operation For initial use, plug the heater into a regular household power point and turn the power on. The timer is now ready to be set up for use. 13 : 17 ON OFF ADVANCE AUTO MAN ON P1 Fig. 4 Setting Current Time 1. Press the ‘PROGRAM’ button ONCE. The clock symbol appears on the top left hand side of the screen. The user can now set the clock. 2. The hour digit will flash. To adjust the hour use the ‘-‘ & ‘+’ buttons. Confirm the hour digit by pressing ‘ENTER’. 3. Once ‘ENTER’ has been pressed the minutes will flash. To adjust the minutes use the ‘-‘&‘+’ buttons. Confirm the minute digit by pressing ‘ENTER’. 4. The timer now returns to the default display. 5. To reset incorrect time, repeat previous steps. Once the correct time is set, a total of four ON/OFF time programs can be set for operation. There are two program options. Setting Programmes Press the ‘PROGRAM’ key twice to set the programs. You are now setting the programs starting with P1 ‘ON’. SETTING P1 ON TIME: 1. To set the hour use the ‘-‘ & ‘+’ buttons. Confirm the hour digit by pressing ‘ENTER’. 2. To set the minutes use the ‘-‘ & ‘+’ buttons. Confirm the minute digit by pressing ‘ENTER’. Note: The minutes can only be set in 10 minute blocks in programme ‘MODE’. SETTING P1 OFF TIME: 3. To set the hour use the ‘-‘ & ‘+’ buttons. Confirm the hour digit by pressing ‘ENTER’. 4. To set the minutes use the ‘-‘ & ‘+’ buttons. Confirm the minute digit by pressing ‘ENTER’. Repeat steps 1 to 4 to programme P2, P3 & P4. After programming P4 ‘OFF’ you automatically exit to the default display. At any time while programming the timer you can press the ‘PROGRAM’ button to exit to the default display. The Advance Function When in ‘AUTO’ MODE, if the ‘+’ button is pressed for longer than 2 seconds the programme will ADVANCE to the next setting programmed and will only revert back to the program when the subsequent programme time is reached. When the ‘ADVANCE’ function is running the ‘ADVANCE’ segment will be displayed on the LCD screen. If the ‘-‘ button is pressed when the ‘ADVANCE’ programme is running the ‘ADVANCE’ feature will be automatically cancelled and the programme will run as normal. Note - Timer Memory Back Up Batteries - Once the heater has been left plugged in with the socket switched ...
Otros modelos de este manual:Eléctrico - DXLAT150 (767.94 kb)
Eléctrico - DXLAT75 (767.94 kb)