Votos - 4, Puntuación media: 4
(
)
)
|
Fotos y especificaciones Scarlett SC-1159 |
Resumen del manual
Do not use for industrial purposes. • Before the first connecting of the appliance check that voltage indicated on the rating label corresponds the mains voltage in your home. • Danger of electric shock exists even when the appliance is switched off. Always unplug the appliance from the power supply when is not use. • Oil heater should never be used under conditions where it may be immersed or come in contact with water, and also do not use the appliance in rooms with the increased moistness. • Do not operate the oil heater with a damaged cord or plug. • Return malfunctioning appliances for repair to near service center. Repair of the device only by qualified persons. • Close supervision is required when appliance is used near children. • Always remove the plug from the power supply before cleaning. • Unplug oil heater by grasping plug and pulling it from the power supply. Pull on the plug, not on the cord. • Do not use out of the room. • Do not insert and pull out the plug with wet hand, as this may cause electrical shock. • The oil heater must be used only in the upright position. • The unit should be far away from the object flammable or easy deformated objects during uses. • Place the oil heater on the floor at least 90 cm away from the wall and any other objects such as furniture, curtains or plants. • Surface temperature of the appliance is high, thus do not touch it, except the handle. CAUTION: • Do not cover the appliance when is use. 2 ASSEMBLING • Do not operate the oil heater without the base support fixed correctly. • To fix the rear support base, fit it tightly against the fin, until it stays in place (as.). • To fix the front support base, fit it tightly against the bottom on the front panel (as.). • After fixing the supports, confirm that the heater is stable on the floor. USING THE APPLIANCE • Set the thermostat to the minimal position and power switch to the “BbiK^.” position, insert the plug to the power supply. THERMOSTAT • The thermostat will automatically maintain your desired room temperature. • Set the power switch to the “Bk^.” position. • Turn the thermostat control clockwise all the way round until you hear a click, this sound indicates that the oil heater is activated, the pilot light is ON. Continue turning the thermostat control clockwise to its highest setting. • When the pilot light is ON, the heater is activated. This light turns ON and OFF repeatedly by order of the thermostat. • Turning the thermostat clockwise will always increase the set temperature; turning it anticlockwise will decrease the set temperature. The thermostat will automatically turn the heater on and off. NOTE: • The room must be sealed in good condition, if not, it will not make good result because of the influx of heat. • After use, turn the thermostat to the minimal position and set the power switch to the “BbiKR” position and unplug from power supply. MAINTENANCE AND CARE • The oil heater should be cleaned regularly to wipe out the dust on the surface of fins. As this may result the radiating efficient. • Unplug from the power supply and allow the appliance to cool down. • Wipe out with a soft damp cloth. Do not use detergent or abrasives. • Do not scrap the surfaces of fins with sharp hard tools, to avoid surfaces getting rusty, because of damage of the paint coat. STORAGE • Ensure the oil heater is completely cool. • Roll up the power cord in the supports when the heater is not in use. • Store the appliance in a cool, dry place. 3 SPECIFICATION Power supply 230 V, 50 Hz Power 1000 W Net / Gross weight 6.40 kg / 7.38 kg Radiating fins quantity 9 Gift box dimension (L x W x H) 465 mm x 135 mm x 430 mm 4 ОПИСАНИЕ 1. Нагревательные элементы 2. Встроенная ручка 3. Термостат 4. Переключатель Вкл./Выкл./Световой индикатор работы 5. Основание 5 1 МЕРЫ БЕЗОПАСНОСТИ При эксплуатации прибора соблюдайте следующие меры предосторожности: • Внимательно прочитайте руководство по эксплуатации. • Использовать только в бытовых целях. Прибор не предназначен для промышленного исполь...