Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
The "Set" temperature is displayed next to the "Room" temp. The unit will cycle on and off to maintain the "Set" temperature. The default room temp = 72.F/22.C. In this mode the unit will run to maintain the "Set" temperature. 2. Press Mode button on remote again. The remote screen displays "Auto" and "high". The "Set" temperature is displayed next to the "Room" temp. The "Auto" light on unit stays illuminated. The unit will cycle on and off to maintain the "Set" temperature at high wattage (1500 Watts). 3. To turn unit "Off", press the Mode button and the LCD will go blank (except for the "Room" temperature display which is always displayed while batteries are in the remote) and the unit will shut off. Note: It is normal for the heater to cycle on and off as it maintains the preset temperature. To prevent the unit from cycling, you need to raise the thermostat setting. ADJUSTING SET TEMP: 1. When in "Auto" mode, press the (+) button on the remote. The "Set" number will increase with each press. Hold the button down to scroll. The minimum temp is 55.F/13.C and the maximum is 85.F/29.C. The unit scrolls one digit at a time in a continuous loop. 55., 56.…, 84., 85., 55., 56.…. 2. When in "Auto" mode, press the (-) button on the remote to decrease the "Set" temperature. The unit scrolls one digit at a time in a continuous loop. UNIT OPERATION WITHOUT REMOTE A. Remote and Unit are OFF: 1. Press the Mode button on the unit the first time. The "Low" light illuminates and the unit runs in "Low" mode. Figure 2 HIGH(1500 Watts) LOW (1000 Watts) AUTO MODE The power light turns on. 2. Press the Mode button a second time to run in "High" mode (1500 Watts). 3. Press the Mode button a third time and the unit shuts off. Note: The "auto" light only illuminates when the unit is set to "auto" mode by the remote. B. Remote is ON and Unit is ON: 1. Press the Mode button on the unit. The unit will then switch "Modes"; either from "Low" to "High" or "High" to "Off". The unit’s lights will reflect the change. The Remote will display a different mode – the mode in which it was left. If a button is pressed on the Remote, the Remote’s signal will override the "Mode" on the unit and the two will be back in sync. TIMER FUNCTION: To turn unit off while remote and unit are on (in low, high, auto state). 1) Hold mode button for 2 seconds to unlock remote. 2) Push + and - together. 2.1) "timer" turns on. 1 Hr appears on the screen. 3) Push + or - to adjust the number of hours the unit will run before it automatically shuts itself off. 3.1) you can choose from; 1 to 8 hours 3.2) 1 through 8 will scroll in a continuous loop 4) After you have made your selection, the whole screen flashes for 5 seconds after last button push of + or then goes back to previous mode 4.1) "timer" remains lit to show the timer function has been set. 5) At any time if you unlock the remote and push the mode button to turn the unit off the timer setting will be erased and "timer" will disappear from the remote. 6.) To check how much time is remaining, press and hold the + and – buttons simultaneously. To turn unit on while remote and unit are off (only ambient temp is displayed on remote). This function is meant for a person to preheat a room by setting the timer. For Example: It’s 8 am, and you want to come home to a warm room at 8 pm. To accomplish this, place the unit in the desired room and set the timer to turn the unit on in 12 hours. Once the timer is activated the unit will run for a preset time of 2 hours. The digital thermostat will maintain the room temperature at a default of 72°F/22.C. 1) Hold mode button for 2 seconds to unlock remote. 2) DO NOT push mode again as this will turn unit on. 3) Push + and - together. 3.1) Unit remains off. 3.2) "timer" and "auto - high" turns on and flashes on the remote, and 1 Hr appears on the screen 4) Push + or - to adjust the number of hours that will pass before it turns itself on. 6 7 4.1) you can choose from 1 to 16 hours 4.2) 1 through 16 will scroll in a continuous loop 5) The whole screen flashes for 5 seconds after last button push of + or - then goes back to previous mode 5.1) "timer" and "auto - high" remain lit to show the timer function has been set. 5.2) The timer will turn the unit on and run for 2 hrs then shut off and maintain the room in auto - high at the default of 72./22.C. After these 2 hours, the unit will shut off. 6) At any time if you unlock the remote and push the mode button on the remote the timer setting will be erased and "timer" will disappear from the screen. 7) To check how much time is remaining, press and hold the + and - buttons simultaneously. CLEANING/MAINTENANCE During Season Care: 1. Always unplug the heater before cleaning 2. Clean the unit with a soft cloth moistened with a mild soap solution. 3. NEVER use abrasive or flammable solvents to clean the unit. 4. After cleaning, be sure to completely dry the unit with a cloth or towel. After Season Care: 1. Store heater in a cool, ...