Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
Repeat for the other wheel then repeat the process to assemble the other wheel support. • Place the heater on the floor upside down. It is quite normal to hear the oil moving inside the radiator. • Holding the bent end, insert the wheel clamp (7) between the last 2 heating fins. Place one assembled wheel support over this, & fit the bent end of the clamp through the hole in the support. • Slide the wheel support towards the bend in the wheel clamp, rotating the clamp as it moves until the free end can be fitted through the other hole. • Tighten the wing nut onto the free end of the clamp. • Repeat this assembly process for the other wheel assembly. Note: When fully assembled, the 2 sets of wheels should be facing away from each other (wheels out). Put the heater into its normal upright position. Wait for at least three minutes before operating the appliance. Heater Operation: • Fully unwind the cord & place the unit on a flat, even floor away from any obstructions and pointing towards the area of the room to be heated. • As a safety mechanism, the oil radiator will not function if the unit is not on a level surface. • Connect the heater to an electrical supply, leaving sufficient space around it for ventilation. • Rotate the thermostat dial (1) to maximum and rotate the heat setting dial to the required heat, 1 low, 2 medium, 3 high. • Once the room is at a comfortable temperature, the thermostat dial (1) should be slowly turned in the opposite direction until the appliance just stops working. • The temperature will be maintained at the present level by the thermostat inside the unit. • When it is no longer necessary to heat the room, return the heating buttons to the off (0) position to turn the unit off and unplug it from the mains supply. Note: To heat the room more quickly the fan heater can be used. This can be activated by pressing the fan button to the on position. Note: This appliance must be attended in use. Warning: In order to avoid overheating, do not cover this appliance. -4 Safety of others • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. • Children must be supervised to ensure that they do not play with the appliance. Safety Fuse: • In case of overheating, a cut-out will operate and the appliance will stop working. If the appliance stops operating, return all heating buttons to the off (0) position, unplug the appliance and allow it to cool for at least 10 minutes before attempting to use it again. • In extreme conditions, a back-up cut-out will operate. This will not re-set & the appliance will need to be repaired by a qualified person. How to take care of your Radiator Cleaning your Radiator • Switch off the appliance before cleaning, changing accessories or approaching parts which move in use. • Do not immerse the appliance, cord set or plug in liquids • Wipe the appliance with a damp cloth & dry thoroughly before using. • Never use detergents or abrasives to clean this appliance. Storing your Radiator • When the appliance is to be stored, return the heating buttons to the off (0) position and unplug it from the mains supply. Additional Safety Warnings: • Do not use this appliance with a programmer, timer or any other device that switches the heater on automatically, since a fire risk exists if the heater is covered or positioned incorrectly. • Do not use this appliance in the immediate surroundings of a bath, a shower or a swimming pool. • Use this appliance on a level surface, away from steps of stairs. • Combustible materials such as furniture, pillows, bedding, papers, clothes and curtains must be kept at least 1m from the appliance. • Do not allow anything to block the vents of the appliance. A gap of at least 50cm is advised. • Always use and store in a dry area. • Do not use in areas where gas, paint or other flammable goods may be present. • This heater is filled with a precise quantity of special oil. Repairs requiring opening of the oil container are only to be made by the manufacturer or his service agent who should be contacted if there is an oil leak. • When scrapping the heater, follow the local regulations concerning the disposal of oil. • Never pull the unit by the cord. Always use the handle provided when moving the appliance. • Always disconnect the appliance from the socket outlet before moving it to a new location. • Keep the cord set away from hot parts of the appliance. • This appliance must be earthed. • This appliance is fitted with a safety device which will prevent the heater working unless it is in its normal, upright working position. -5 Protecting the environment Separate collection. This product must not be disposed of with normal household waste. Should you find one day that your Black & Decker product needs replacement...