Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
2. Extinguish any open flame. 3. if odor continues ,immediately call gas supplier. FOR YOUR SAFETY Do not store or use gasoline or other flammable vapors or liquids in the vicinity of this or any other appliance. WARNING: For Outdoor Use Only. CAUTION: Retain the instructions for future use. C E R T I F I E D ISGE ND CDE ER ITFI Manual,Instructions & Parts List 2 TOOLS AND PARTS NEEDED FOR ASSEMBLY TOOLS NEEDED: 7/16 Wrench 3/8 Open End Wrench Adjustable Opening Wrench, 8 Long Philips Head Screwdriver Leak Detection Solution ( Instructions how to make solution are included in Step 8 ) 3 PARTS 15 17 1 Regulator 1 Cylinder (Not Supplied) 1 2 3 4 5 6 7 8 9 10 11 4 Reflector Cap 1 Head Assembly 1 Gas Hose 1 Post 1 Cylinder Cover 1 Cylinder Base 15 M6 Nuts 18 6mm Washers 5 M4 x 8 Bolts 3 Post Mounts 10 12 1 Center Reflector Cap 12 M6 x 10 Bolts 13 15 16 3 M6 x70 double pointed bolts 14 5 4mm Washers 12 13 9 17 16 6 M5 x 8 Bolts 18 6 5mm Washers 11 14 2 4 5 7 6 3 1 8 14 16 17 10 9 15 13 ASSEMBLY FOR LIGHT SYSTEM ASSEMBLY FOR LIGHT SYSTEMASSEMBLY FOR LIGHT SYSTEM WARNING: TO BE INSTALLED ONLY BY AN AUTHORISED PERSON Instruction For Battery Installing Upon first time use of the product,please remove the ignition button and install an AAA battery as indicated. Ignition button Control knob Replace Battery Ignition button AAA battery 5 ASSEMBLYASSEMBLY ASSEMBLYASSEMBLY NOTE: Assembly of this heater requires basic mechanical skills. Proper assembly is the responsibility of the installer. Step 1 ---Step 1 Step 2 ---Step 2 M5 X 8 bolts (6 pcs) and 5mm washers (6 pcs) Attach the post to the post mounts using Attach Post to Base Assembly 7 Attach Cylinder Cover to Post Mounts Attach the cylinder cover to the post mounts. 7 6 14 11 5 6 ASSEMBLYASSEMBLY ASSEMBLYASSEMBLY NOTE: Assembly of this heater requires basic mechanical skills. Proper assembly is the responsibility of the installer. Step 3 ----Attach Head Assembly to Post Load head assembly by inserting gas hose into post. Insert head assembly into post. Tighten securely using M4 X 8 Bolts (5 pcs) and 4mm washers (5 pcs). Step4 ----Attach Double Pointed Bolt to Head Assembly Attach M6 X 70 double pointed bolts (3 pcs) and 6mm washers (3 pcs) to the top of head assembly and tighten the bolts securely. Step 3 Step 4 3 5 3 13 16 10 12 4 7 ASSEMBLYASSEMBLY ASSEMBLYASSEMBLY NOTE: Assembly of this heater requires basic mechanical skills. Proper assembly is the responsibility of the installer. Step 5 ----Attach Center Reflector to Reflector Attach center reflector to the top of reflector (4 pcs) by M6 X 10 mm screws (12 pcs) , 6mm washers (12 pcs) and nuts (12 pcs). Step 6 ----Attach Center Reflector and Reflector to the top of Head Assembly Load center reflector and reflector to the top of head assembly by M6 X 70 double pointed bolts (3 pcs) 6mm washers (3 pcs) and nuts (3 pcs) Step 5 2 1 15 10 9 Step 6 3 10 9 8 ASSEMBLYASSEMBLY ASSEMBLYASSEMBLY NOTE: Assembly of this heater requires basic mechanical skills. Proper assembly is the responsibility of the installer. Step 7 ----Connect Gas Line to Cylinder Attach Gas hose to regulator with 3/8 Inch Open End Wrench and Adjustable Wrench. Attach regulator to cylinder. Tighten securely. Move cylinder to the plate of base assembly. Step 8 ----Check for leak Your Patio Heater has been checked at all factory connections for leaks, To check the Connection of the gas hose/regulator/cylinder. 1) Make leak solution by mixing 1part liquid dish soap and 3 parts water. 2) Spoon several drops (or use squirt bottle) of the solution onto the gas hose/regulator and regulator/cylinder connection. 3) Inspect the connections and look for bubbles. 4) If no bubbles appear, the connection is safe. 5) If bubble appear, there is leak, loosen and re-tighten this connection. Step 7 Step 8 9 ASSEMBLYASSEMBLY ASSEMBLYASSEMBLY WARNING : TO BE INSTALLED ONLY BY A COMPETENT PERSON Step 9----Lower Cylinder Cover ontoCylinder Base Lower the cylinder cover onto the cylinder base . Step 10----Disconnect CylinderWhen Storing or Transporting 1).Turn off the heater; 2).Upper the cylinder cover onto the post mounts; 3).Turn off the valve of the cylinder; 4).Loosen the screw of cylinder and regulator; 5).Disconnect the cylinder from regulator. Step 9 6 8 Step 10 6 7 10 OPERATIONOPERATION OPERATIONOPERATION WARNING: DO NOT attempt to operate heater until you have read and understand all precautions. Failure to do so can result in serious personal injury, deathor property damage. Before Turning Gas Supply ON Your heater was designed and approved for OUTDOOR USE ONLY. Do NOT use it inside a building ,or any other enclosed area. Make sure surrounding areas are free of combustible materials, gasoline and other flammable vapors or liquids. Ensure that there is no obstruction to air ventilation. Be sure all gas connections are tight and there are no leaks. Be sure the access panel is clear of debris. Be sure any component removed during assembly or servicing is replaced and f...