Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
20. DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user serviceable parts. Qualified personnel should perform all servicing only. 21. Connect to properly grounded outlets only. 22. SAVE THESE INSTRUCTIONS. WARNING: This heater has a voltage rating of 120 volts. The cord has a plug as shown in A. An adapter as shown in C is available for connecting three-blade grounding-type plugs to two-slot receptacles. The grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptacle is available. DO NOT DEFEAT THE SAFETY PURPOSE OF THE GROUNDED PLUG. SPECIFICATIONS Voltage Rating 120 V (60Hz) Power Consumption 700/800/1500W Unit Size 24 in. (W) x 24 in. (D) x 36 in. (H) Unit Weight 19 lbs Control Switches Decorative Cone Base Pole Control Switches Decorative Cone Base Pole PRODUCT DIAGRAM Heater Head Weighted Base ASSEMBLY PARTS Remove all contents from the packaging. A The packaging includes the following items: A) 1 Heater head B) 1 Weighted Base C) 1 Decorative Cone D) 1 Base Pole E) 2 Heater Head Connector Screws F) 3 Base Bolts G) 3 Nuts for the base bolts H) 1 Assembly Wrench (Not Pictured) I) 1 Allen Wrench (Not Pictured) C NOTE: The screws, bolts, assembly wrench, and Allen wrench are wrapped in a plastic bag and placed on the underside of the Styrofoam next to the weighted base. B E D F G BASIC ASSEMBLY To properly assemble this heater you need the supplied assembly wrench and Allen wrench (or one of your own). Refer to the parts diagram on page 5 while assembling the heater. PLEASE NOTE: The design of the base in the images below will slightly differ from the base provided with the heater. 1) First, attach the base pole (D) to the weighted base (B) using the 3 base bolts (F) and 3 nuts (G). Once you secure the base pole (D) to the weighted base (B), place the decorative cone (C) over the base pole (D) to cover the bolts on the base. 2) Next, place the power cord attached to the heater head (A) through the middle of the base pole (D). Pull the power cord through the bottom of the base as far as it will go. 3) Next, connect the heater head to the base pole. To do this, align the small screw holes on top of the base pole (D) with the holes on the bottom of the heater head (A). Use the small heater head connector screws (E) to secure the heater head (A) to the base pole (D). BASIC ASSEMBLY (CONTINUED) 4) Before using the heater, align the power cord with the cutout on the weighted base and secure using the attached fasteners on the bottom of the weighted base. There is one fastener located near the middle of the weighted base, and another fastener located near the cutout at the end of the base. Place the cord through each fastener and tighten to secure the cord to the base. After securing the power cord to the fasteners, place the rubber ring located around the power cord in the cutout on the weighted base. Properly attaching the power cord to the weighted bases will allow the heater to be moved easily and prevent damage to the power cord. OPERATING INSTRUCTIONS Place the heater on a firm, level surface and plug into a grounded 120V 60Hz power outlet. Only operate the heater when it is in the upright position and the base is attached. Refer to the diagram below. The HP2-15-50 Electric Patio Heater is equipped with three heat settings; Low, Medium, and High. • To operate the heater on low, press the red switch on the right. This switch will have a single white dot near the top. Once the low switch is pressed, the smaller bottom heating element will glow and radiate heat. • To operate the heater on medium, press the red switch on the left. This switch will have two white dots near the top. Once the medium switch is pressed, the larger top heating element will glow and radiate heat. • To operate the heater on high, press both the low and medium red switches. This will cause both the bottom and top heating elements to glow and radiate heat. HEATER CONTROLS MAINTENANCE Unplug the unit and let it cool completely. • To keep the heater clean, the outer shell may be cleaned with a soft, damp cloth. You may use a mild detergent if necessary. After cleaning, dry the unit with a soft cloth. • DO NOT use alcohol, gasoline, abrasive powders, furniture polish, or rough brushes to clean the heater. This may cause damage or deterioration to the surface of the heater. • Although this heater is outdoor approved, DO NOT immerse the heater in water for your safety. Wait until the unit is completely dry before use. WHEN THE HEATER IS NOT IN USE When not using the heater for an extended period of time, place the electrical cord inside the decorative cone that covers the bottom part of the pole. To do so, simply lift the cone and wrap the electrical cord around the bottom pole. When the cord is completely w...