Votos - 5, Puntuación media: 3.8
(
)
)
|
Resumen del manual
NOTE: After several seconds, the LCD screen will fade, but the heater settings will remain visible. Use the MODE button to select the desired heat setting. The mode button allows you to scroll through the various heating modes. HIGH – High heat setting (1800 watts) LOW – Low heat setting (1100 watts) AUTO – for use with the electronic thermostat FAN – for fan only operation To switch the heater into standby mode, press and hold the POWER/ SWING button until a beep sound is heard. Turn the heater off by switching the Power switch located on the right hand side of the base, to the off position. NOTE: This heater features a tip-over switch. If the heater tips over, it will automatically switch off. Once placed back into the upright position, the heater will be in standby mode, and the settings will need to be selected again. Before First Use Remove any promotional material or packaging from the heater. Unwind the cord to its full length and place the heater on a firm, level surface in a stable upright position. Visually inspect the air inlet and outlets to ensure there are no blockages. When unpacking the heater, check to see you have received the remote control, before discarding the packaging. Turning Your Heater On Plug the cord into a 230V or 240V power point and switch on. NOTE: To avoid an electrical circuit overload, it is recommended that no other appliances are plugged into the same circuit as your heater, when it is in use. Turn the heater on by switching the On/Off switch located on the left hand side of the base, to the on position. An audible beep will sound, and the red power indicator light will illuminate. The heater is now in standby mode. Setting the Heating Mode KCE540_IB_FA.indd 8 12/10/09 9:29 AM 9 Setting the Variable Temperature The variable temperature setting can be used to maintain your desired temperature. NOTE: The variable temperature setting only operates when the heater is being used in the Auto mode. Press the MODE button until the heater is set to AUTO mode. The LCD screen will display the default temperature of 25°C and will flash. When the temperature is flashing, you may set the desired temperature pressing the VARIABLE TEMPERATURE buttons on the control panel. To adjust the set temperature press the VARIABLE TEMPERATURE button to increase the desired temperature or press the VARIABLE TEMPERATURE button to decrease the desired temperature. The temperature can be set between 15°C and 35°C. When the air temperature reaches 2-3°C above the set temperature, the heater will automatically cut out, although the fan will continue to run for approximately 20 seconds to cool the heater. When the air temperature drops below the set temperature the unit will begin heating again. Setting the Oscillation The oscillation function works in all operating modes. Press the POWER/SWING button once to activate. The heater will begin to oscillate from side to side. Press the POWER/SWING button again to stop the heater from oscillating. Setting the Auto-Off Timer The timer function works in all operating modes, and switches the unit off after a preset number of hours. Press the TIMER button to activate the timer settings. A timer symbol will appear on the LCD screen displaying 1 hour. Press the TIMER button to cycle through the one hour increments, up to 8 hours. The unit will then switch itself to standby mode after the selected number of hours has passed. Safety Features This heater includes an audible alarm to warn that parts of the heater are overheating. If the alarm sounds, immediately turn the heater off and inspect for any objects on or adjacent to the heater that may cause high temperature. DO NOT OPERATE THE HEATER WITH THE ALARM SOUNDING. KCE540_IB_FA.indd 9 12/10/09 9:29 AM NOTE: The variable temperature setting only operates when the heater is being used in the Auto mode. Press the MODE button until the heater is set to AUTO mode. The LCD screen will display the default temperature of 25°C and will flash. When the temperature is flashing, you may set the desired temperature pressing the VARIABLE TEMPERATURE buttons on the control panel. To adjust the set temperature press the VARIABLE TEMPERATURE button to increase the desired temperature or press the VARIABLE TEMPERATURE button to decrease the desired temperature. The temperature can be set between 15°C and 35°C. When the air temperature reaches 2-3°C above the set temperature, the heater will automatically cut out, although the fan will continue to run for approximately 20 seconds to cool the heater. When the air temperature drops below the set temperature the unit will begin heating again. Setting the Oscillation The oscillation function works in all operating modes. Press the POWER/SWING button once to activate. The heater will begin to oscillate from side to side. Press the POWER/SWING button again to stop the heater from oscillating. Setting the Auto-Off Timer The timer function works in all operating modes, and switches the uni...