Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
The Power-On Indicator, on the front of the heater, will illuminate when the heater is turned on. Remove any promotional material or packaging from the heater. Unwind the cord to its full length and place the heater on a firm, level surface in a stable upright position. Visually inspect the air inlet and outlets to ensure there are no blockages. Assembling Your Heater Remove all items from the packaging - the carbon tower body, front and rear bases. Unscrew the two screws from the base of the tower body. To join the front and rear bases together, initially feed the cord between the two parts of the base. Position the front base over the corresponding posts of the rear base, and press down to fit the bases together. Ensure the cord remains within the channel formed when the two halves come together. Turn the carbon tower body upside down. Align and position the base over the corresponding posts on the rear of the tower body. Push down the base onto the tower body until it is firmly held into position. KCF200_IB_V4.indd 8 21/10/09 9:34 AM 9 Setting the Heating Mode CAUTION: DO NOT COVER SWING HIGH MODE OFF LOW 30 0 MINS 60 90 120 150 TIMER 180 ON To control the heater, turn the MODE dial as follows. The Heat Setting dial has 3 modes: OFF -Shuts off the heater 1 -Low heat setting (500W) 2 -High heat setting (1000W) Once the heat setting has been selected, turn the TIMER dial to the ON position. This will activate the heater. NOTE: The Carbon Tower Heater will not activate while the Timer dial is set at 0 MINS. To switch the heater off, turn the MODE dial to the OFF position. NOTE: This heater features a tip- over switch. If the heater tips over, it will automatically switch off. Once placed back into the upright position, the heater will activate again. Setting the Auto-Off Timer The TIMER function works in all operating modes, and switches the unit off after a preset number of hours. Turn the TIMER dial to activate the timer settings. The timer can be set for up to 3 hours. For setting times less than 1 hour, turn the timer dial past the 2 hours mark, then turn back to the desired time. The unit will then switch itself off after the selected time has passed. By turning the TIMER dial to ON, this will ensure the heater runs continuously, and will not turn itself off. Setting the Oscillation The oscillation function works in all operating modes. Press the SWING button once to activate. The heater will begin to oscillate from side to side. Press the SWING button again to stop the heater from oscillating. KCF200_IB_V4.indd 9 21/10/09 9:34 AM CAUTION: DO NOT COVER SWING HIGH MODE OFF LOW 30 0 MINS 60 90 120 150 TIMER 180 ON To control the heater, turn the MODE dial as follows. The Heat Setting dial has 3 modes: OFF -Shuts off the heater 1 -Low heat setting (500W) 2 -High heat setting (1000W) Once the heat setting has been selected, turn the TIMER dial to the ON position. This will activate the heater. NOTE: The Carbon Tower Heater will not activate while the Timer dial is set at 0 MINS. To switch the heater off, turn the MODE dial to the OFF position. NOTE: This heater features a tip- over switch. If the heater tips over, it will automatically switch off. Once placed back into the upright position, the heater will activate again. Setting the Auto-Off Timer The TIMER function works in all operating modes, and switches the unit off after a preset number of hours. Turn the TIMER dial to activate the timer settings. The timer can be set for up to 3 hours. For setting times less than 1 hour, turn the timer dial past the 2 hours mark, then turn back to the desired time. The unit will then switch itself off after the selected time has passed. By turning the TIMER dial to ON, this will ensure the heater runs continuously, and will not turn itself off. Setting the Oscillation The oscillation function works in all operating modes. Press the SWING button once to activate. The heater will begin to oscillate from side to side. Press the SWING button again to stop the heater from oscillating. KCF200_IB_V4.indd 9 21/10/09 9:34 AM 10 ThermoGuard Overheating Safety Device Your heater is fitted with a safety device that switches off the heater in the event of overheating. Should this heater stop working, turn off the heater and inspect the air inlet and outlet for blockages. Wait at least five minutes for the protection system to reset before attempting to restart the heater. If the heater fails to operate or the safety device switches off again, return the heater to your nearest Kambrook service centre for examination or repair. Using Your Carbon Tower Heater continued KCF200_IB_V4.indd 10 21/10/09 9:34 AM Your heater is fitted with a safety device that switches off the heater in the event of overheating. Should this heater stop working, turn off the heater and inspect the air inlet and outlet for blockages. Wait at least five minutes for the protection system to reset before attempting to restart the heater. If the heater fails t...