Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
• Consult the dealer or an experienced radio/TV technician for help. ¦ CAUTION CHANGES OR MODIFICATIONS NOT APPROVED BY JVC COULD VOID USER’S AUTHORITY TO OPERATE THE EQUIPMENT. PRECAUTION Contents Installation Method Memo . The dome cover and base are connected with fall prevention wire. Note . Before touching the camera unit, make sure to touch the metal surface of the [MONITOR] terminal to discharge any static electricity from your body. Static electricity may cause the camera to malfunction. Dear Customer, This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety. European representative of Victor Company of Japan Limited.is: JVC Technology Centre Europe GmbH P.O.Box 10 05 52 61145 Friedberg Germany Instructions 1 Warranty Card 1 Service Information Card 1 Desiccant (Service Parts No.LW40790-001A) 1 HEATER UNIT 1 Wrench (Supplied) Fall Prevention Wire Inner Dome Lug(x 3) * TK-C215VP4 is used in the illustration. LST0472-001A Step2: Mounting this unit onto TK-C215VP series 1. Install TK-C215VP series on the ceiling Refer to TK-C215VP series “INSTRUCTIONS” for the installation method. 2. Mounting this unit onto Space for Heater of TK-C215VP series • Mount this unit onto DOME CAMERA as shown in the right figure. • Insert the claw of this unit into Space for Heater. Make sure to mount properly. • After inserting this unit into Space for Heater, make sure to tighten the fastening screw of this unit with a + screwdriver. 3. Connecting cable Connect the cable to the [to HEATER] terminal of TK-C215VP series. Step3: Adjust the field of view and lens of the camera Switch on the power supply of the camera. Refer to TK-C215VP series “INSTRUCTIONS” on how to adjust the field of view and lens of the camera. After adjusting the field of view and lens of the camera, switch off the power supply of the camera. Step4: Install the inner dome Mount the inner dome to the 3 lugs. Step5: Inserting the Desiccant supplied Take out the desiccant from the aluminum package, insert it into the desiccant insertion space of the camera unit and fasten using the lug plate. Step6: Installing the dome cover 1. Cleaning the dome cover Before mounting, remove any dust or dirt from the dome cover. 2. Mounting the dome cover to the base Mount the dome cover by aligning the 3 position marks on the base with the dome cover. 3. Fastening the dome cover Fasten by tightening the 3 fastening screws of the dome cover using the wrench supplied. Step7: Check items after installation Check the following items after installation. . Is the power supply for TK-C215VP series AC 24 V? . Have you inserted the desiccant that comes with this unit? . Does an image appear normally on the monitor after switching on the power for TK-C215VP series? . Is the cable of this unit connected to the [to HEATER] terminal of TK-C215VP series? . Has the fastening screw of this unit been tightened properly? o Dimensions(Unit: mm) * Design and specifications are subject to change without notice. Note . Mount the inner dome such that it does not cover the lens. . When mounting the inner dome, make sure not to move the position of the lens. Doing so may cause the preset angle of view to go out of alignment. Memo . During reconnection or re-installation after repair or maintenance, make sure to replace the desiccant with a new one. . Consult your nearby JVC’s dealer on the replacement procedures. Serial number of part to be replaced: Use a LW40790-001A desiccant. Note . When mounting is performed on a rainy day, make sure that rain water does not enter this unit. . Make sure to use the desiccant supplied. Failure to do so may cause the camera lens and dome cover to fog. . If the angle of view is not adjusted immediately after mounting the camera, insert the desiccant after adjustment is completed. The desiccant loses its effect if it is exposed to the air for a prolonged period of time. 2. 3. [to HEATER] terminal Space for Heater HEATER fastening hole Space for Heater [to HEATER] terminal HEATER fastening hole Fastening Screws Claw Cable Cable * TK-C215VP4 is used in the illustration. Lug(x 3) Inner Dome * TK-C215VP4 is used in the illustration. Desiccant Insertion Space Desiccant Lug Plate * TK-C215VP4 is used in the illustration. Memo . Dirt that is not removed from the cover before mounting may appear on the camera’s image. . Do not apply excessive force to the dome cover such as stretching it. Note .When mounting the dome cover, take note that the desiccant is not caught between base and dome cover. Specifications Power supply / Voltage :AC 24 V ± 10%, 60 Hz/50 Hz Power consumption :18 W (during AC 24 V) Heater operation :Surrounding temperature -22 °F to 32°F ( -30f to 0f)(auto on/off) * By using this unit, the operation guarantee temperature of the camera becomes -22 °F to 122°F (-30f to 50f) Mass :56 g Accessories :Instructions .......................................... Warranty Card .......