Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
FF520 Page 23 7. Move the ShuttlePoint knob to highlight YES and press [ENTER] to confirm. 8. Press [CLEAR] to exit. WARNING Turn Off and after few seconds turn On the Fish Finder in case of failed firmware upload. 3.4 SYSTEM INFORMATION PAGE FOR CP180/CP180i/CPV350 For troubleshooting you maybe asked by a Standard Horizon Product Support Technician for the software version of Fish Finder. The following procedure is how to access this information. 1. From the Chart Page, press [MENU] for two times to open the Setup Menu. 2. Move the ShuttlePoint knob to highlight ABOUT... and press [ENT] or move the ShuttlePoint knob to the right. 3. A window will be shown with the system information on the Fish Finder Library version and on the Fish Finder module type and version. 4. Press [CLR] to exit. 3.4.0 The System Update menu The System Update menu allows downloading the Fish Finder firmware into the Fish Finder device. To select this menu follow the procedure: 1. From the Chart Page, press [MENU] for two times to open the Setup Menu. 2. Move the ShuttlePoint knob to highlight ABOUT... and press [ENT] or move the ShuttlePoint knob to the right. 3. A window will be shown with the system information. 4. Press [MENU]. 5. Move the ShuttlePoint knob to highlight BBFF FIRMWARE SOFTWARE and press [ENT] or move the ShuttlePoint knob to the right. 6. The current Fish Finder firmware version is shown in the System Update window that appears on the screen. Insert the C-CARD with the firmware in one of the GPS Chart Plotter available slots, and the press [ENT] to update. 7. Move the ShuttlePoint knob to highlight YES and press [ENT] to confirm. 8. Press [CLR] to exit. WARNING Turn Off and after few seconds turn On the Fish Finder in case of failed firmware upload. Page 24 FF520 4. FISH FINDER SETUP MENU · From the Full Fish Finder page, press [MENU] to show the Fish Finder Setup menu. Figure 4 -Fish Finder Setup menu · From the Chart page, to access this menu: 1. Press [MENU], move the ShuttlePoint knob to SETUP and press [ENTER]. 2. Move the ShuttlePoint knob to FISH FINDER SETUP and press [ENTER]. The following paragraphs describe the Fish Finder Setup menu sub-options. 4.0 PRESETS Allows selection of the following preset modes: FISH, CRUISE. The default values are: Fish : Gain mode = Auto, Range mode = Auto Range, Gain Offset = 0%, Shift = 0, STC = Short, Noise Level = 2, Scrolling Speed = 10, Fish Symbols = Echo, A-Scope = On, Surface Declutter = 0. Cruise : Gain mode = Auto, Range mode = Auto Range, Gain Offset = 10%, Shift = 0, STC = Short, Noise Level = 4, Scrolling Speed = 10, Fish Symbols = Echo, A-Scope = On, Surface Declutter = 4. NOTE For Gain and Gain Offset settings please see the Sensitivity menu (Par. 4.5). For Range and Shift settings see the Range menu (see Par. 4.3). 4.1 PAGE SELECTION The Page Selection menu allows you to adjust the Fish Finder display page to your preference, sizing the Chart and Fish Finder page (see also Par. 3.1.0a). FF520 Page 25 Figure 4.1 -Page Selection sub-menu The Page Selection options are: Auto : Selects automatically the 50kHz if depth is greater than 400 ft and selects 200kHz if depth is less than 300 ft Full Display : Shows the full Fish Finder page allowing to select among the 200kHz Standard Fish Finder, 50 kHz Standard Fish Finder or 200/50 kHz Dual Fish Finder. Chart/Fish : Shows the Chart page on the left half of the screen and the Fish Finder on the right half of the screen. It is possible to select among the 200kHz Standard Fish Finder or 50 kHz Standard Fish Finder. Zoom Full page : Shows the zoomed Fish Finder on the left half of the screen and the unzoomed Fish Finder on the right half of the screen. It is possible to select between the 200kHz Split Fish Finder or the 50 kHz Split Fish Finder zoomed view. 4.2 GAIN MODE Selects Auto or Manual. 4.3 RANGE MENU The Range menu allows you to set the Fish Finder working range. The Depth and Shift functions allow the Fish Finder display to be changed from showing information between the bottom of the transducer and the bottom to a range you want to select. Figure 4.3 -Range sub-menu The Range options are: Range Mode : Selects among Manual, Auto Range and Bottom Lock. In Manual Range Mode is possible to set Shift (the offset from the surface) and depth on which the Fish Finder shall operate. In Auto Range Mode the Fish Finder determines automatically the range as to keep the bottom visible in the lower bottom of the screen. In this mode, Shift is always set to 0. In Bottom Lock Mode the Fish Finder Page 26 FF520 automatically tracks the range around the bottom specified by the Bottom Range value. Depth : Moves the display from showing the bottom to the depth value entered. Shift : Shifts the display from the bottom of the transducer to the depth value entered. Example Your vessel is in about 57FT of water, however there is fish suspended in 35FT of water. You want to display to 10FT area around the fish. Shift would be set to...
Otros modelos de este manual:Sounders - Ff520 (3.41 mb)