Votos - 3, Puntuación media: 3.7 ( )

Fabricar: Humminbird Tamaño del archivo: 992.83 kb Nombre del archivo: Idioma del manual:

3. Secure the mount arms with the 4 #6 screws provided (Figure 5). Hand tighten only! 4. Set the assembled control head base in place on the mounting surface. Mark the four mounting screw locations with a pencil or punch. 5. Set the base aside, and drill the four mounting screw holes using a 9/64" bit. 6. Proceed to Routing the Control Head Cables Under the Deck. 4 Control Head Installation Routing the Control Head Cables Under the Deck Use the following steps to route the control head cables under the deck. NOTE: Under the deck cable routing is not always possible. If this is not an option, the cables should be routed and secured above deck. NOTE: See the installation section for your transducer type in order to plan the location of the transducer and cable route. Tilt Mount or Tilt and Swivel Mount Tilt Mount or Tilt and Swivel Mount: Control Head Base 1a. Mark and drill a 3/4" hole as shown in Figure 6. Route the cables through the hole. The cables will exit through the center hole on the control head base. 1b. If the cables cannot be routed directly beneath the control head base, mark and drill a 3/4" hole that will allow you to run the cables close to the control head base. 3/4” 19mmFigure 6 5 Control Head Installation Attaching the Control Head to the Base Follow these steps to attach the control head to the already-assembled base: NOTE: The transducer cable and power cable should be routed prior to securing the mounting bracket to the deck. 1. Apply marine-grade silicone sealant to the drilled holes for the mounting bracket. 2. Place the mounting bracket on the mounting surface, aligning with the drilled holes. 3. Insert the four #8 Phillips countersink wood screws into the mounting holes and hand tighten only! PivotKnuckleGimbalKnobThumbknobBoltFigure7MountingHoles 4. Insert the thumbknob bolt through the pivot knuckle on the control head (Figure 7). 5. Align the pivot knuckle with the mount base arms and slide into place, twisting slightly if necessary, until the unit is firmly seated. 6. Rotate the control head to the desired angle and hand tighten the thumbknob bolt. 7. Thread the gimbal knob onto the pivot bolt and tighten. 6 Control Head Installation Attaching the Cables to the Control Head Follow these steps to attach the power and transducer cables to the control head: 1. Matching the cable plugs to the shape and orientation of the sockets, insert the transducer and power cables into the correct sockets on the control head (Figure 8). Power Temperature Transducer 2. With the control head in place, tilt and/or swivel the unit through its full range to make sure there is enough cable slack for the unit to move freely. Hand tighten the thumbknob bolt when you achieve the desired position for the control head. You are now ready to install the transducer. See Transducer Installation Overview and then find the section that refers to your transducer type. Figure8 7 Transducer Installation Overview Transducer Installation Overview The transducer can be installed on the transom of the boat, inside the hull, or onto a trolling motor, depending on your transducer type. The type of transducer you have will also determine how the cable will be routed. Go to the section that describes your transducer, and follow the steps to position and mount the transducer on your boat. NOTE: Due to the wide variety of hulls, only general instructions are presented in this installation guide. Each boat hull represents a unique set of requirements that should be evaluated prior to installation. It is important to read the instructions completely and understand the mounting guidelines before beginning installation. NOTE: If the included transducer will not work for your application, you may exchange it, NEW and UNASSEMBLED, with mounting hardware included, for a transducer appropriate for your application -often at very little or no charge depending on the transducer. Call the Humminbird® Customer Resource Center at 1-800-633-1468 for details and pricing, or visit NOTE: In addition to the hardware supplied with your transducer, you will need a powered hand drill and various drill bits, various hand tools, including a ruler or straightedge, a level, a 12" plumb line (weighted string or monofilament line), marker or pencil, safety glasses and dust mask, and marine-grade silicone sealant. NOTE: When drilling holes in fiberglass hulls, it is best to start with a smaller bit and use progressively larger drill bits to reduce the chance of chipping or flaking the outer coating. 8 Transom Transducer Installation Transom Transducer Installation Locating the Transducer Mounting Position Turbulence: You must first determine the best location on the transom to install the transducer. It is very important to locate the transducer in an area that is relatively free of turbulent water. Consider the following to find the best location with the least amount of turbulence: AreasofPossibleTurbulenceRivetsStrakesTransomHul...

Descargar ahora

Introduzca dos números de la imagen: