Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Step 2. Push the leg tips on the round ends of the lower leg sections. (The other ends have a wire.) Step 3. Put the wire end of lower leg sections into the round end of the upper leg sections. Push the sections together while twisting lower leg slightly. This will ensure a snug fit. Step 4. CHECK: Lift swing as shown. If legs are assembled properly, the legs will dangle from the motor unit and not fall off. IF LEG FALLS: Holding leg vertically, push leg firmly up while pushing the motor unit down. Step 5. Open the swing legs completely. Snap plastic leg braces onto outside of legs. The plastic pins inside the ends of the braces will fit into the dimples on the legs. It may be necessary to spread the legs as shown. Do not use swing without the leg braces. Wire end Dimple Hold tube vertically Flattened side Plastic peg Attaching the Hanger Step 1. With crossbar of hanger toward front of the motor unit, line up holes in hanger brackets with holes on the sides of motor unit. Step 2. Insert screws into both brackets as shown. Fasten with acorn nuts using the enclosed hex wrench. Tighten nuts firmly with hex wrench and screwdriver. Step Lift turn with Step Snap together handle plastic Step Place Be seated Step Place Step Set the Your only Step Give swinging Using Infant Lift the swing. Step 1. With baby out of swing, open the battery compartment by gently pressing on the lid at the ridged area and lifting the lid. Step 2. Insert four .D. cells. Be sure the batteries are put in correctly. (Swing will not run if batteries are put in backwards.) Step 3. Snap the lid closed. Using the Cradle Not intended for use as a night-time bed or car bed. REMOVE LAW TAGS FROM CRADLE PAD AND QUILTED SHEET BEFORE USING THIS CRADLE. Step 1. Cover soft side of cradle pad with quilted sheet provided. Installing Batteries NEVER INSERT OR REMOVE BATTERIES WITH BABY IN THE SEAT. THEY COULD FALL ON BABY IF DROPPED! Round end (not oval) Push Push 7 8 Adjusting the Handle To bring infant carrier handle from resting position into position for carrying or swinging, first set the carrier down. Then push down on center of handle, and rotate the handle forward until it clicks into the locked position. To return the handle to resting position, first set the carrier down. Then push down on center of handle, and rotate the handle backward until it clicks into place. NOTE: It is normal for the handle to seem loose in the resting position. Using the Tray Unlatch the tray by squeezing the two latches under the tray at the same time, and lift up tray. Be careful not to let tray hit your baby when lifting or closing tray. To latch tray, push down firmly. Tray must be latched at all times when baby is in the swing. Adjusting the Stand To change recline of the carrier, squeeze the adjustment wire and move to desired position. To adjust for rocking, move the adjustment wire to the highest position. Do not change recline with baby in infant carrier. Be aware that infant movement or rocking may cause the infant carrier to move on a table. Push down on center of handle Push down on center of handle Different uses for infant carrier... Cuddler Carrier Feeder ...or as a Rocker. Hanger Notch Step 2. Lift top frame of cradle, and turn handle so that it lines up with the plastic hinges. Step 3. Snap handle and hinges together to lock. Be sure handle is locked into the plastic hinges. Step 4. Place cradle in hanger. Be sure handle notches are seated in the hanger. Step 5. Place your child in the cradle. Step 6. Set the control switch between the low and medium positions. Your cradle will swing properly only in the lower range. Step 7. Give cradle a push to start the swinging motion. Using the Infant Carrier Lift carrier in and out of swing. Do not adjust the handle while carrier is on swing. Do baby baby Keep Any a (put replaced Any disposed charge Never recharger Discard batteries sure according Always for cause Do baby Keep Any a put replaced Any disposed charge Never recharger Discard sonal Always Using the Swin. CHECK that all parts ar. securely fastened togethe. before using the swing. Step 1. Place carrier in hanger. Be sure handle notches ar. seated in the hanger. Step 2. Thread both sides of seat bel. through the buckles as shown. CHEC. that the belt is thread. ed correctly by pulling on th. seat belt. The belt should no. slip through the buckle. Step 3. Open tray and place baby i. the seat. (If your child is ver. small, you may want to us. rolled-up blankets as a prop.. Step 4. Place crotch strap betwee. child.s legs and snap both sid. buckles to the center buckle. Adjust belt as needed to get . snug fit around your child. HangerNotch Caring Problem: Swingwon'toperateSeatdoesn'tswingveryhighChange Tbuckle. Step 5. Close the traytray is latched by pulling upon the trayDo not depend on the tray or seatbelt alone to hold your baby. Always secure yourbaby with both the seat belt and tray when yourchild is in the swing. Step 6. Adjust the control switch t. me...