Votos - 5, Puntuación media: 4.2
(
)
)
|
Resumen del manual
CAUTION: Do not operate this fireplace with a broken glass door panel. Do not operate this fireplace without the glass door panel securely in place. For replacement part information see Replacement Parts, page 35. Figure 47 - Removing/Replacing Glass Door Glass Door Assembly Screw Lower Bracket for Glass Door Assembly 1. Remove the upper louver panel by lifting upward and out (see Figure 46). 2. Remove the screws from the three tabs at the top of the glass door while holding door securely keeping it from falling forward. 3. Grasp door by both sides and ease it upward off of the lower bracket (see Figure 47). 4. To replace glass door, follow the above instructions in reverse. Top Louver Panel Figure 46 - Removing Top Louver Panel 22 106497 OWNER’S MANUAL FIREPLACE INSTALLATION Continued Left Side INSTALLING OPTIONAL Brick Panel BRICK LINER D8037A/D8041 WARNING: If fireplace has been running, turn off and unplug fireplace. Let cool before installing brick liner. This brick liner kit is optional. You may purchase brick liner from your local dealer or see Accessories, page 38. CAUTION: Always handle brick panels with two hands. Do not force brick panels into place. Excessive force will break brick panels. 1. Remove glass door. See Removing/Replacing Glass Door, page 22. 2. If installing brick liner in new fireplace, go to step 3. If installing brick liner in an existing fireplace, carefully remove logs, lava rock, and ember material. 3. Install left side brick panel first by sliding it between the grate and the side of the firebox (see Figure 48). 4. Slide the left retainer bracket against the left side brick panel. Loosely secure the bracket screw. This secures the left side brick panel. 5. Install the right brick panel using the same method described in step 3. 6. Slide the right retainer bracket against the right side brick panel. Loosely secure the bracket screw. This secures the right side brick panel. 7. Install rear brick panel. Rest bottom edge of panel on back edge of grate (see Figure 49). 8. Loosely secure retainer brackets to grate. Brackets are adjustable left to right to allow proper placement of panel. These will hold rear panel in place. 9. Tighten all bracket screws. 10. Follow instructions on page 24 to install logs, lava rock, and ember material. 11. Replace glass door (see page 22). Figure 48 - Installing Left Side Brick Panel Rear Brick Panel Retaining Brackets Figure 49 - Installing Rear Brick Panel and Retainer Brackets Continued 106497 23 ® DIRECT-VENT FIREPLACE FIREPLACE INSTALLATION Continued INSTALLING LOGS, LAVA ROCK AND GLOWING EMBERS WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this heater may result in property damage or personal injury. Each log is marked with a number. These numbers will help you identify the log when installing. It is very important to install these logs exactly as instructed. Do not modify logs. Only use logs supplied with fireplace. Remove glass door. See Removing/Replacing Glass Door, page 22. Install logs according to instructions for fireplace model numbers. Fireplace Models MBDV37 and MBDV41 1. Place log #1 (back log) on top of grate. Make sure the notches in the bottom of the log fit over the grate (see Figure 50). 2. Rest log #2 (large front log) on the pins on the front part of the grate (see Figure 51). 3. Place log #3 (“C”-shaped crossover log) onto the rear and front logs. Make sure it is seated properly on the smooth surface on the front log and on the pin on the back log as shown in Figure 52. 4. Place log #4 (small, round log) on the pin on the right side of front log as shown in Figure 53 5. Place log #5 (small log) onto the front left part of the grate making sure the notches fit over the prongs of the grate (and hole over pin on 41" set). See Figure 54. 6. Place lava rock along sides and front of firebox bottom in areas that are visible only. It is not necessary to use all of the lava rock provided. NOTICE: Do not put lava rock on burner or under burner. Placing lava rock on burner could cause performance problems. 7. Pull ember material apart into pieces no larger than a dime. Place these pieces loosely and sparingly directly onto the exposed section of the front burner and along the space between the burner and grate prongs (see Figure 55). This will create the glowing ember appearance as the flame touches the ember material. Do not block air slots by using too much ember material in one area. It is not necessary to use all of the ember material provided. 8. Replace the glass door. See Removing/ Replacing Glass Door, page 22. WARNING: The glass door must be securely in place before running this fireplace. Do not run this fireplace if glass is missing or broken. 1 Figure 50 -Installing Log No. 1 2 Figure 51 - Installing Log No. 2 3 Figure 52 - Installing Log No. 3 4 Figure 53 - Installing Log No. 4 5 Ember Material 41" Set Only Figure 54 - Installing Log No. 5...
Otros modelos de este manual:chimeneas - MBDV41 (997.31 kb)