Votos - , Puntuación media:
(
)
)
Fabricar: Lennox Hearth
Tamaño del archivo: 1.01 mb
Nombre del archivo: 048ac3d3-72c4-4bde-86e3-dc5dda63a1f7.pdf
Idioma del manual:
El documento se está cargando, por favor, espere
 |
El documento se está cargando, por favor, espere
Resumen del manual
NC 06/2008 INSTALLATION INSTRUCTIONS FOR fACADE KITS for use with ADAGIO™ Direct-Vent Gas Fireplaces TM KIT CONTENTS: Facade Kit 1 ea. Facade Assembly (1) 1 ea. Instruction Sheet INSTALL ONLY WHEN FIREPLACE IS OFF AND COOL. ALL WARNINGS, PRECAUTIONS AND INSTRUCTIONS PROVIDED IN THE INSTALLATION INSTRUCTIONS MANUAL AND THE CARE AND OPERATION MANUAL PROVIDED WITH THE APP LIANCE APP LY TO THESE INSTRUCTIONS. THOROUGHLY READ AND FOLLOW THE INSTRUCTIONS PROVIDED WITH THE APPLIANCE BEFORE PROCEEDING TO THE FOLLOWING INSTRUCTIONS. Installation instructions 1. Install the appliance, firebox liner and logs per the Installation Instructions Manual provided with the appliance and the Installation Instruction Sheet provided with the firebox liner kit (sold separately). 2. Using a 3/8” socket or nutdriver, remove heat shield, screen retainer and screen from facade. See Figure 2. Cat. No Model Description H5773 ADAGIO-AG Arched Face Black Facade H5774 ADAGIO-PF Arched Face Brushed Nickel Facade The arched facade kits require a filigree inset kit. These kits are sold separately. Contact your dealer for ordering information. Filigree Inset Kits (Sold Separately - Required) Cat. No. Model Description H6845 ADAGIO-INSET-ASPEN-BK Aspen, Black H6846 ADAGIO-INSET-ASPEN-BN Aspen, Brushed Nickel H6847 ADAGIO-INSET-ASPEN-BKN Aspen, Black Nickel H6848 ADAGIO-INSET-ASPEN-G Aspen, Gold H6849 ADAGIO-INSET-NAPA-BK Napa, Black H6850 ADAGIO-INSET-NAPA-BN Napa, Brushed Nickel H6851 ADAGIO-INSET-NAPA-BKN Napa, Black Nickel H6852 ADAGIO-INSET-NAPA-G Napa, Gold H6853 ADAGIO-INSET-TUSCAN-BK Tuscan, Black H6854 ADAGIO-INSET-TUSCAN-BN Tuscan, Brushed Nickel H6855 ADAGIO-INSET-TUSCAN-BKN Tuscan, Black Nickel H6856 ADAGIO-INSET-TUSCAN-G Tuscan, Gold Filigree Inset Kit 1 ea. Upper Filigree inset (2) 1 ea. Lower Filigree inset (3) 7 ea. Washers #10 (4) 7 ea. Hex Head Nuts (5) Installer: Leave This Instruction Sheet With The Appliance. Consumer: Retain This Instruction Sheet For Future Reference. Figure 1 TOOLS / SUPPLIES NEEDED: 3/8” Socket or Nutdriver General information The arched facade kits are offered in two attractive finishes, black and brushed nickel. If you encounter any problems or need clarification of these instructions, contact you local distributor or dealer. Note: The base of the appliance will need to be elevated by 3/4" minimum above the floor to allow for the proper fit of the facade (i.e. 3/4" board as platform). See Installation Instructions Manual. FPO 4 7 Places 5 7 Places 2 3 1 5. Install the facade onto the fireplace face per instructions in Figure 3. 6. See Figure 4 for instructions on accessing the control compartment. To access the control compartment, pull the hinged door forward and up as shown. To close, hinge the door closed until magnets secure it in place. Figure 4 - Opening the Control Compartment Panel Figure 5 - Completed Installation IMPORTANT NOTE (Gold and Nickel Finishes Only): The gold and nickel finishes will require heat to harden and cure (after approximately 3 fires, the finish will be completely cured). Prior to burning this appliance the gold and nickel surfaces should be cleaned thoroughly with a good window cleaning solution and a soft cloth. Do not use any metal polishes or abrasives to clean the surfaces. Any oils or fingerprints left on the finish during the curing process may become permanent blemishes. Magnets Control Compartment Control Compartment Panel Facade 3. Using a 3/8” socket or nutdriver, install the upper filigree inset, lower filigree inset, screen and screen retainer with provided washers and nuts as shown in Figure 2. Note: you will have four extra washers and nuts. 4. Reinstall heat shield aligning the top corners of the heat shield with the etch marks in the back of the facade for proper placement. Do not over tighten nuts. Figure 2 Brushed Nickel Facade Shown Figure 3 - Install Facade Tabs on Bracket Assemblies (2 places each side) Slots on Fireplace (2 places each side) Facade Align the tabs on the bracket assemblies all the way into the slots on fireplace, then push facade down to ensure engagement. Printed in U.S.A. © 2008 Lennox Hearth Products P/N 750,231M REV. NC 06/2008 Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and the discontinuance of colors, styles and products. Consult your local distributor for fireplace / insert code information. NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Lennox Hearth Products 1110 West Taft Avenue • Orange, CA 92865 Note: There are two mounting positions on the facade hanging brackets to better accommodate a range of facing thicknesses. Adjust to the notch on the hanging bracket that works best for your installation. Heat Shield Upper Filigree Lower Filigree Screen Screen Retainer Etch Marks ...