Votos - 6, Puntuación media: 4.2
(
)
)
|
Resumen del manual
FIREPLACE SPECIFICATIONS - SSDVST (SEE-THROUGH ) PRODUCT REFERENCE INFORMATION Cat. No. Model Ship Wt. Ship. Volume H3333 SSDVST-CNM 282 lbs 52W x 27D x 44-1/2H (36.2 cu.ft). H3334 SSDVST-CNE 282 lbs 52W x 27D x 44-1/2H (36.2 cu.ft). Figure 12 SPECIFICATIONS Natural and Propane Gas BTU Input 37,500 (MV Low 30,000) Co-axial DV Vent Size 4-1/2" Inner 7-1/2" Outer NOTES • Annual Fuel Utilization Efficiency Diagrams, illustrations and photographs are not to scale – consult installation instructions. Product designs, materials, dimensions, specifications, colors and prices are subject to change or discontinuance without notice. Appliance has a factory-installed vent seal cap (see Figures 15 and 16 on Page 13) in each flue outlet. EFFICIENCIES SSDVST 61% (NG) 62 % (LP) Steady State 72 % (NG) 73 % (LP) • AFUE68 % (NG) 68 % (LP) 6-7/8 (175) 10-1/4 10-1/2 (260) 12 (305) 12 (305) 10 (254) (63.5) 3 (76) FLUE (Top or Side) (267) FLUE (Top or Side) GAS INLET ELECTRICAL INLETS GAS INLET 40-1/8 (1019) (16) (89) 3 (76) ELECTRICAL INLETS FRAMING SPACERS (Top and Both Sides) 24 (610) FINISH WALL BRACKET (Front and back edge of unit top) 1/2(13) 3-1/2 3-1/2 (89) ELECTRICAL INLETS(940) 37 41 (1041) 4 (102) (13) (1197) 47-1/8 (873) 34-3/8 (610) 24 (63.5) Detail fo Finish Wall Bracket 2-1/2 2-1/21/2 (13)1/25/8 *41-1/2 (1054) 48-1/2(1108) (679) 11-3/8 (267) (289) 7 (178) 5-1/8 (130) 12-1/8 (308) 10-1/2 22-3/4(578) 6-1/4 (159) A 7 (178) 5-1/8 (130) 12-1/8 (308) 26-3/4 Provide additional space for Side Vent Seal Cap if installing against a solid wall. Louvered Control Compartment DoorLeft Side View Front View Right Side View Top View Stepped to Accept Drywall (all 4 corners) **25-1/4(641) 10-1/2(267) 12-1/8(308) 5-1/8(130) 12-1/8(308) 26-3/4(648) 5-1/8(130) Vent Center - Top Vent with one 90 degree elbow * This dimension can be reduced to 41 inches (1041 mm). This results in 0 in. (0 mm) clearance between framing and unit framing spacers. (The 41-1/2 in. dimension permits easier fireplace installation, if unit is installed after framing is erected). ** This dimension based on 5/8" drywall. For 1/2" drywall use 25-1/2" (648 mm). The finished dimension should be 26-1/2" (673 mm). See also, Side Vent Seal Cap note below. • Inches (millimeters) • Minimum Framing Stud Size is 2 x 4 • See side views of fireplace below for gas line inlet location options. Vent Framing - Top Vent With One 90. Elbow Vent Framing - Rear Vent With No Elbows Gas Line Center of gas line is 3 in. (76 mm) up from floor. Gas Line A Vertical Venting Through the Ceiling: Frame ceiling opening -Use a plumb line from the ceiling above the appliance to locate center of the vertical run. Cut and/or frame an opening, 10-1/2" x 10-1/2" (267 mm x 267 mm) inside dimensions, about this center mark (see Figure 19 on Page 15). Vent Center- Side Vent (no elbows) Dimension A Secure Vent 47-1/8 (1194) Secure Flex 47-7/8 (1216) NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. FIREPLACE SPECIFICATIONS - SSDVPF (PENINSULA VIEW) Fireplace Framing Specifications Figure 13 12 (305) 10 (254) 40-1/8(1019) 3-1/2(89) (16) FRAMING SPACERS (Top and Side) FINISH WALL BRACKET (Front, back, and left edge of unit top) 6-7/8(175) 10-1/4 (260) 12 (305)(63.5) 3 (76) (13) 1/2 1/2 5/8 DETAIL OF FINISH WALL BRACKET FLUE (Top or Side) 2-1/224 (610) 41 (1041) 37 (940) 43-5/8 (1108) (13) 4 (102) GAS INLET ELECTRICAL INLETS 2-1/2 (63.5) FLUE (Top or Side) (873) 34-3/8 (610) 24 (610) 24 (464) 18-1/4 *41-1/2(1054) 43-5/8(1108) (679) 11-3/8 (267) 7 (178) 5-1/8(130) 12-1/8(308) 10-1/2 22-3/4 (578) inches (millimeters) Gas Line Center of gas line is 3 in. (76 mm) up from floor. 6-1/4(159) A Minimum Framing Stud Size is 2 x 4 7 (178) 12-1/8(308) 5-1/8(130) Dimension A Secure Vent -46-1/2 (1181) Secure Flex -48-1/4 (1226) 26-3/4 PRODUCT REFERENCE INFORMATION Cat. No. Model Ship Wt. Ship. Volume H3335 SSDVPF-CNM 270 lbs 52W x 27D x 44-1/2H (36.2 cu.ft). H3336 SSDVPF-CNE 270 lbs 52W x 27D x 44-1/2H (36.2 cu.ft). SPECIFICATIONS Natural & Propane Gas BTU Input 37,500 (MV Low 30,000) Co-axial DV Vent Size 4-1/2" Inner 7-1/2" Outer NOTES • Annual Fuel Utilization Efficiency Diagrams, illustrations and photographs are not to scale – consult installation instructions. Product designs, materials, dimensions, specifications, colors and prices are subject to change or discontinuance without notice. Appliance has a factory-installed vent seal cap (see Figures 15 and 16 on Page 13) in each flue outlet. EFFICIENCIES SSDVPF 58 % (NG) 61 % (LP) Steady State 72 % (NG) 73 % (LP) • AFUE68 % (NG) 68 % (LP) Louvered Control Compartment DoorLeft Side View Top View * This dimension can be reduced to 41 inches (1041 mm). This results in 0 in. (0 mm) clearance between framing and unit framing spacers. (The 41-1/2 in. dimension permits easier fireplace installation, if unit is installed after framing is erected). ** This dimension based on 5/8" drywall. For 1/2" drywall use 25-1/2" (648 mm). The finished dimension should be 26-1/2" (673 ...
Otros modelos de este manual:chimeneas - SSDVPF-CNE-B (4.94 mb)
chimeneas - SSDVPF-CNE-B (4.94 mb)
chimeneas - SSDVPF-CNE-B (4.94 mb)
chimeneas - SSDVPF-CNE-B (4.94 mb)