Votos - 3, Puntuación media: 5
(
)
)
|
Resumen del manual
A vacuum can be used to remove any dust accumulation on the blower’s blades or inside the blower duct. Caution should be used not to damage the blower’s blades during cleaning. To reinstall the blower, slide the blower back into the retaining lip B and retighten screws A. A Adjustable Hopper The Winslow™ PI40 insert is shipped with the 55 pound hopper. With the larger hopper installed, that part of the insert that slides into the fireplace is 22-1/2” (572 mm) high. For installations in smaller fireboxes, the hopper is adjustable down to a height of 19” (483 mm). To adjust the hopper to its lowest height of 19” (483 mm), remove screws C around the hopper lid and lift the lid off. Next, remove the screws D around the hopper extension and remove the extension. Place the lid back over the hopper and reinstall the screws securing the lid. To adjust the hopper height between the maximum and the minimum, remove screws D and slide the hopper extension (with lid attached) down around the hopper bottom to the height desired. The extension can be loweredatmost2-1/2”(64mm).Reinstalltheself-tappingscrewsthrough Figure 39 the holes in the extension (creating new holes in the hopper bottom). Proof of Fire Switch This switch needs to be removed and cleaned after every 100 bags of fuel burned. Cleaning Procedure: 1. UNPLUG STOVE! 2. Locate the switch on the combustion blower (see Figure 43). 3. Using a flat-head screwdriver, remove the 2 screws which secures the switch to the blower housing. 4. Using a dry cloth, wipe off any flyash build-up on the sensor portion of the switch. 5. Reinstall switch. Ensure wires are properly connected to the switch and the connectors are not making contact with the blower housing. Close side panel. Note: Failure to clean the proof of fire switch when needed may result in nuisance shut-downs because the fly-ash build-up insulates heat from reaching the switch. (Recommended Frequency of 1 year or after every 100 bags of fuel used) Blower Duct Slide to the side to remove. B Hopper Extension Hopper Lid C Figure40D NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Front Door Opening and Removal CAUTION: Do not open the front door when the insert is hot. To remove the door, swing the left and right side doors A open. Pull the front door handle B to the front and swing the front door open. Lift the front door up and off the hinges as shown in Figure 41 (see C). To reinstall the door repeat the steps in reverse order. Side Door Removal To remove the door, 1. Swing the door open 2. Lift the door up, and 3. Pull the bottom of the door out and down - pulling the top hinge pin out of the retaining hole in the top hinge bracket. To reinstall the door, slide the pin on the top of the door up and into the hole in the upper hinge bracket. Slide the pin on the bottom of the door into the hole in the pedestal base and rotate the door closed. B 3 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 3 C A Front Door Figure41 1 Side Door Figure42 COMPONENT INFORMATION The following is a list of components and their functions. Igniter The Winslow™ PI40 insert comes equipped with an automatic igniter for lighting the fuel when the insert is in the lighting mode. The igniter superheats air that is pulled through the burn pot by the combustion blower to light the fuel. The igniter remains energized for the first seven minutes of the lighting sequence. Vacuum Switch The Winslow PI40 insert has a vacuum switch located behind the left door, fastened to the base (see A in Figure 44). If there is a leak in the firebox created by the front door being ajar or a blocked flue, the vacuum switch will sense it and cause the insert to go into a shutdown mode. Auger and Auger Motor The 1.25 RPM auger motor (B in Figure 22) turns the auger lifting pellets up the auger tube. The pellets are then dropped down a tube and into the firepot. The auger is controlled by the control board. Over Temperature Snap Switch (Opens at 225F) This switch is installed on the convection blower (see C in Figure 44) and shuts the insert down if it senses excessive temperatures. This snap switch has a reset button on it and will not allow the insert to start up until the reset button has been pushed. Proof of Fire Snap Switch (Closes at 140° F) This switch is installed on the combustion blower and shuts the insert down if it does not detect fire in the burn pot. Convection Blower Snap Switch (Closes at 120° F) This switch is installed on the right rear of the firebox and turns the convection blower on when the insert gets up to temperature. Figure 44 NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. 4 Combustion Blower Figure43 A B C Room Air (Convection) Blower Draft Adjuster Draft Adjuster of the insert directly in front of the combustion blower. Should the insert installation require long runs of vent pipe, a situation may be created where excessive combustion air is flowing through the firebox and causing the fuel to burn faster than it can be delivered ...
Otros modelos de este manual:chimeneas - WINSLOW PI40 (2.1 mb)
chimeneas - WINSLOW PI40 (2.1 mb)
chimeneas - WINSLOW PI40 (2.1 mb)