Votos - 2, Puntuación media: 4.5 ( )

Fabricar: Napoleon Fireplaces Tamaño del archivo: 1.02 mb Nombre del archivo: Idioma del manual:

Allow two inches of material for a flange on all sides and cut to these measurements. Bend down the flanges. If you have never done this before, it might be a good idea to make a cardboard pattern and test it first. Fasten this flue cover in position as high as possible with two masonry screws per side through the flanges into the FLANGE MODEL 1401 Illustrated fireplace. FIGURE 13. DAMPER REMOVED OR FASTENED OPEN FLUE CONNECTOR LISTED CHIMNEY LINER 2" FLUE COVER INSTALLATION FIGURE 13 In Canada: Install a listed 6 inch diameter flexible stainless steel liner from the top of the chimney to the insert flue collar. Attach a stainless steel liner connector or elbow to the liner and insert onto the flue collar. Fasten with three screws. Secure the top of the liner to the chimney cap using a liner support and chimney flashing. Cap the top of the chimney liner assembly using an approved rain cap. W415-0512 /C 10.02.06 In the United States: While it is not required, it is recommended that a chimney liner be installed that is continuous from the insert to the top of the chimney, particularly when the insert is installed in a basement. For this type of connection, use the "In Canada" installation instructions above. In the United States: While it is not required, it is recommended that a chimney liner be installed that is continuous from the insert to the top of the chimney, particularly when the insert is installed in a basement. For this type of connection, use the "In Canada" installation instructions above. If a continuous liner is not installed, a "direct flue connection" must be made. The direct flue connection requires a non-combustible connector that extends from the insert into the chimney flue liner and also that the installed flue cover be sealed below the entry point of the connector to prevent dilution of combustion products in the chimney flue with air from inside the house. Cap the top of the chimney using an approved rain cap. 1401/1402 INSERT MODEL An optional low clearance flue connector is available to facilitate hook up into a tight fitting fireplace. Consult your local dealer for details. The following installation requirements must be observed when installing solid fuel burning inserts into factory built fireplaces. INSTALLATION INTO A FACTORY BUILT FIREPLACE 1. The factory built fireplace must be listed per UL 127 or ULC S610. 2. Clearances to any combustible material surrounding this insert as identified in Figure 10 must be followed. These clearance requirements supersede any pre-existing facing material clearances listed for the factory built fireplace. 3. Installation must include a full height listed chimney liner meeting HT requirements (2100°F) per 1777 (U.S.) or ULC S635 (Canada). The liner must be securely attached to the insert flue collar and the chimney top. 4. Means must be provided to prevent room air passage to the chimney cavity of the fireplace. This may be accomplished by sealing the damper area around the chimney liner, or sealing the fireplace front. 5. The air flow within and around the fireplace shall not be altered by the installation of the insert (i.e. no louvres or cooling air inlet or outlet ports are blocked), unless specifically tested as such for each factory built fireplace manufacturer and model line. (Note - using a louvred face plate (surround) complies with this requirement) 6. Alteration of the fireplace in any manner is not permitted with the following exceptions; a. external trim pieces which do not affect the operation of the fireplace may be removed providing they can be stored on or within the fireplace for reassembly if the insert is removed. b. the chimney damper may be removed to install the chimney liner. 7. Circulating air chambers (i.e. in a steel fireplace liner or metal heat circulator) shall not be blocked. 8. Means must be provided for removal of the insert to clean the chimney flue. 9. Inserts that project in front of the fireplace must be supplied with appropriate support means. 10. A permanent metal warning label must be attached to the back of the fireplace stating that the fireplace must be restored to its original condition for safe use without the insert. W415-0512 / C 10.02.06 OPTIONAL BLOWER Drywall dust will penetrate into the blower bearings, causing irreparable damage. Care must be taken to prevent drywall dust from coming into contact with the blower or its compartment. Any damage resulting from this condition is not covered by the warranty policy. Use of the blower increases the output of heat. STOVE MODELS Provisions have been made on the stove to install an optional blower kit (EP62-1) that comes complete with a variable speed switch to turn the blower on and off, as well as adjusting the blower speed. An optional thermostatic sensor control kit, EP36, to thermally activate the blower is also available. LEG MODELS ONLY Note: if the optional blower ( EP62-1) is installed, the blower guard (W320-0011) must be installed. This guard...

Descargar ahora

Introduzca dos números de la imagen: