Votos - 3, Puntuación media: 4.3
(
)
)
|
Resumen del manual
These weak, blue and transparent flames are termed anemic. • Propane models may exhibit flames which candle or appear stringy. If this is present and persists, adjust the air shutter to a more closed position, then operate the appliance for a few more minutes to ensure that the flame normalizes and the flames do not appear sooty. The following chart is provided to aid you in achieving the correct air shutter adjustment for your installation. Air Shutter Adjustment Guidelines: Amount of Primary Air Flame Color Air Shutter Adjustment If air shutter is closed too far Flame will be orange Air shutter gap should be increased If air shutter is open too far Flame will be blue Air shutter gap should be decreased NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Burner Air Shutter Adjustment Procedure Burner Air Shutter Adjustment Procedure WARNINGS •Air shutter adjustment should only be performed by a qualified professional service technician. •Ensure front glass panel are in place and sealed during adjustment. CAUTIONS •Soot will be produced if the air shutter is closed too much. Any damage due to carboning resulting from improperly setting the air shutter is n ot covered under the warranty. • The air shutter door and nearby appliance surfacesare hot. Exercise caution to avoid injury while adjusting flame appearance. 1. Locate adjustment rod and adjust air shutter to the standard setting as shown in Figure 56 (adjustment rod is located in the lower control compartment). Note: Move the adjustment rod down to decreases air and up to increases. 2. Light appliance (follow lighting procedure on lighting label in control compartment or see care and operation manual). 3. Allow the burner to operate for at least 15 minutes while observing the flame continuously to ensure that the proper flame appearance has been achieved (see Figure 57). If the following conditions are present, adjust accordingly. • Ifflameappearsweakorsooty,adjust airshutter,incrementally,toa more open position until the proper flame appearance is achieved. • Ifflamestaysloweredblue,adjustairshutter,incrementally,toamore closed position until the proper flame appearance is achieved. 4. Leave the control knob (off/pilot/on) in the ON position and the burner OFF/ON switch OFF (and remote switches, if applicable). 5. When satisfied that the burner flame appearance is normal, re-install the lower control compartment door then proceed to finish the installation. Main Burner Factory Air Shutter Opening Setting - Inches (millimeter) Model Natural Gas Propane Gas SDV35 1/4 (6.35 mm) 1/2 (12.7 mm) Adjustment Rod Up (Fully Open Position) Air Shutter Adjustment Rod Down (minimum air opening position) Burner Tube Adjustment Setscrew Ref. Air shutter Patent: U.S. Pat. 5,553,603 Figure 56 -Burner Air Shutter Adjustment Figure 57 Burner Flame Appearance Model SDV35 Step 10. HOOD INSTALLATION (Refer to Figure 58) All of these appliances must have hoods installed prior to operating. Install hood by sliding it into the slots on the lower edge of the cabinet top. FINISHING REQUIREMENTS - Wall Details Complete finished interior wall. To install the appliance facing flush with the finished wall, position framework to accommodate the thickness of the finished wall (Figure 58). See Page 5 for Cold Climate Insulation and Page 8 for Clearances and Hearth Extension Requirements Combustible Finished Wall Materials Top of Appliance Combustible material may touch the appliance top Louvers Top of Door Frame Hood must be installed as shown. 3" (76 mm) This Area Must Remain Clear of Combustible Materials 1 in. Min. (25 mm) Drywall Bracket / Spacer Top Spacers Figure 58 -Combustible Wall Framing Header NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE. Step 11. ATTACHING SAFETY-IN-OPERATION WARNINGS Step 11. ATTACHING SAFETY-IN-OPERATION WARNINGS ATTACHING SAFETY-IN-OPERATION WARNINGS Your fireplace has been furnished with safety instruction labels that are to be affixed to the operation and control point of the fireplace. A safety instruction label should be affixed to the wall switch plate where the fireplace is turned on and off (See Figure A) or wall thermostat (See Figure B) and if used on the remote control handheld transmitter (Figure C). The warnings should already have been put in place when the fireplace initial set-up was completed. If they are not affixed at these spots, locate the multi-lingual adhesive labels provided with these instructions and proceed as follows: 1. Locate the wall switch or wall thermostat that controls the fireplace (verify the switch operates the fireplace by turning it on and off). Clean the wall switch plate or wall thermostat thoroughly to remove any dust and oils. Affix the label to the surface of the plate of the wall switch that controls the fireplace (Figure A) or the wall thermostat (Figure B). Choose the language primarily spoken in the home. 2. Ifaremotecontrolisusedtocontrolthefireplace, locate the transmitter and clean it thoroughly to remove...
Otros modelos de este manual:chimeneas - SDV35 (4.91 mb)
chimeneas - SDV35 (4.91 mb)
chimeneas - SDV35 (4.91 mb)
chimeneas - SDV35 (4.91 mb)