Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Make sure propane tank valve outlet is clean. • Inspect hose before use. Replace if there is evidence of abrasion or wear. • During set up, check all connections and fittings for leaks using soapy water. Never use a flame. • Use as a heating appliance only. Do not use for cooking. Never alter in any way or use with any device or part not expressly approved by Coleman. • Never burn wood or other fuels with this appliance. Assembly TOOLS REQUIRED: A standard Phillips head screwdriver is the only tool ¦ Loosely install support ¦ Insert tab into slot. required for assembly (not provided). brackets to base. ¦ Install top screw as shown. 3 ¦ Remove all components from package. Step 1 13 Required 1 Required Large Screw Small Screw 1 Required Small Screw 2 Required Large Screw Assembly cont. Step 1 (cont) ¦ Install two cover pieces to base. 5 Required Large Screw Step 2 ¦ Install top support ring between cover and support brackets. 3 Required Large Screw Step 3 ¦ Place collar ring in position as ¦ Load fire pan assembly. shown. Fire Pan Support Ring NOTE: Make sure no wires are pinched between fire pan and support ring. ¦ Install 3 Phillips Head screws ¦ Unit is now ready for final through support ring in location assembly. shown. Tighten screws. 3 Required Large Screw Step 4 ¦ Install log center piece. ¦ Install log support ring so that ¦ Notches in Support Ring must “A” is to the front of the unit match Electrodes on Burner. (Control Panel side). Notches Electrodes Burner ¦ Logs are marked A, B, C, D, E, which match markings on log support ring. A B C D E Assembly cont. Step 4 (cont) ¦ The support ring and each log is marked with a Letter which corresponds to the location where logs should be placed. Each log also has recesses that are lettered which indicate where adjoining logs are to be placed. Start with log “A” then “B”, etc. Step 5 • You must provide propane gas and propane tank. Use a standard 20 lb. propane tank only. The L.P. cylinder must have a shut-off valve terminating in a Type 1 L.P. gas cylinder valve outlet. • Use this fireplace only with a propane vapor withdrawal supply system. See Chapter 5 of the Standard for Storage and Handling of Liquefied Petroleum Gas, ANSI/NFPA 58. Your local library or fire department will have this book. • A minimum supply pressure of 11.0 W.C. is required for the purpose of input adjustment for propane gas. • The pressure regulator and hose assembly supplied with the fireplace must be used. • The installation must conform with local codes, or in the absence of local codes, with National Fuel Gas Code, ANSI Z223.1. • A dented, rusted or damaged propane tank may be hazardous and should be checked by your tank supplier. Never use a propane tank with a damaged valve connection. • The propane tank must be constructed and marked in accordance with the specifications for LP gas cylinders of the U.S. Department of Transportation (DOT). • Never connect an unregulated propane tank to the heater. Standard 20 lb. tank Step 5 (cont) ¦ Attach regulator to tank. ¦ Install tank. Leak Check WARNING • Perform leak test outdoors. • Extinguish all open flames. • NEVER leak test when smoking. • Do not use the fireplace until connection has been leak tested and does not leak. Cylinder Valve Regulator/Cylinder Connection • Make 2-3 oz. of leak check solution (one part liquid dishwashing detergent and three parts water). • Apply several drops of solution where regulator connects to Cylinder. • Make sure control knob is OFF. 5Control Knob • Turn Cylinder Valve ON. If bubbles appear at connection, there is a leak. • Turn Cylinder Valve OFF. • If leak is at Regulator/Cylinder Valve connection: disconnect, reconnect, and perform another leak check. If you continue to see bubbles after several attempts, cylinder valve is defective and should be returned to cylinder’s place of purchase. If NO bubbles appear at connection, the connection is secure. • Turn Cylinder Valve OFF. NOTE: Whenever gas connection is loosened or removed, you must perform a leak test. Operation DANGER • CARBON MONOXIDE HAZARD • For outdoor use only. Never use inside house, or other unventilated or enclosed areas. This fireplace consumes air (oxygen). Do not use in unventilated or enclosed areas to avoid endangering your life. DANGER • EXPLOSION - FIRE HAZARD • Never store propane near high heat, open flames, pilot lights, direct sunlight, other ignition sources or where temperatures exceed 120 degrees F (49°C). • Propane is heavier than air and can accumulate in low places. If you smell gas, leave the area immediately. • Never install or remove propane tank while fireplace is lighted, near flame, pilot lights, other ignition sources or while fireplace is hot to touch. • This fireplace is red hot during use and can ignite flammables too close to the burner. Keep flammables at least two feet from sides & eight feet from top. Keep gasoline and other flammable liquids and vapors well away from fireplace. • The propane tank must ...