Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
12.Visually check that none of the wires in the control compartment have been dislodged from the controls. If they have, use the wiring diagram on the unit or in the instruction manual to replace them in their proper location. 13. Turn the power to the unit on at the breaker/fuse panel. Place the unit into operation and check to make sure that all of the systems are working properly. Service Instructions WARNING: Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electrical shock or personal injury. Remove Front Cover Access to heater/fan 1. Turn off power to the unit. 2. Let fireplace cool if it has been operating. 3. Remove fixed front panel, or open doors (depending on model). If the model has operable glass or mesh doors, completely remove them from the unit before proceeding. To remove the doors, locate and remove the two (2) screws holding the door at the top. (Fig. 2) Hold the door at all times with one hand to prevent the door from falling when you undo the hinge screws. Remove Screws Front Cover Fig. 2 Remove screws holding door at top. 4. Locate the screws that hold the front cover in place. There are six (6) screws, three (3) located on the front of the unit (Fig. 3), and three (3) located underneath the top shelf of the unit. (Fig. 4) Remove Screws Fig. 3 Remove three (3) screws on front of unit. Remove Screws Fig. 4 Remove three (3) screws located under top shelf. 5. Remove screws using appropriate screwdriver. 6. Pull out the front cover. holding both sides of the cover, pull gently towards you and down. Fig. 5 Hold both sides and pull gently forward and down. 7. You now have access to the heater/fan unit, for cleaning and/or maintenance. 8. To reinstall the front cover, please follow reverse procedure, paying attention not to damage any wiring in the process. Glass Information 1. Under no circumstances should this product be operated with broken glass. 2. Do not strike or slam the glass. 3. Do not use abrasive cleaners to clean the glass. 4. This product uses tempered glass. Replacement of the glass supplied by the manufacturer should be done by a qualified service person. Replacing the Light Bulbs Depending on your model, the fireplace uses two (2) or three (3) clear 120 Volt, 60 Watt, E-12 socket base light bulbs (small base, chandelier candle type) located under the ember bed. Units with overhead lights (Fig. 9) use two (2) clear 120 Volt, 5 Watt, E-12 socket base light bulbs (small base, chandelier candle type) located above the logs. For convenience, if one of the light bulbs burns out, it may be easier to replace all of the light bulbs at the same time. Do not exceed 60 Watts per bulb for the ember bed bulbs and 5 Watts per bulb for the overhead lights. Use of higher rated bulbs may result in a fire, causing property damage, personal injury or loss of life. 1. Turn off power to the unit. 2. Let fireplace cool if it has been operating. 3. Remove fixed front panel, or open doors (depending on model). 4. Locate two (2) screws that hold the refractory (brick patterned) bracket together with the ember bed. (Fig. 6) (Not applicable to HEF22) Remove Screws Fig. 6 Remove screws that hold refractory bracket with ember bed. 5. Remove those two (2) screws using an appropriate screwdriver. One screw is located on either side of the unit. Pull Here (both sides) Fig. 7 Pull ember bed out of unit. 6. Pull the ember bed out of the unit, by gently pulling towards you and only slightly upwards. Depending on the model, you can remove the refractory prior to removing the ember bed. 7. Looking into the opening of the unit under the ember bed, visually locate the light bulbs. 8. Remove the light bulbs by unscrewing them out of the bases, turning them counterclockwise. You can use one hand to hold the light socket in place, if required. 60 W Light Bulbs Fig. 8 Remove and replace light 60 W bulb(s). 5 W Light Bulb Fig. 9 Remove and replace 5 W bulb(s). 9. Install the new light bulb(s) by turning the light bulb into the base clockwise. You can use one hand to hold the light socket in place, if required. 10.Reposition the ember bed. If required, gently raise the refractory panels, one at a time, to tuck the ember bed edge underneath them. 11.Reposition the refractory bracket, aligning the refractory in place as required. 12.Reinstall the two (2) screws removed in Step 5. 10008388 CleaningMaintenance of Motors The motors used on the fan and the drum assembly are prelubricated for extended bearing life and require no further lubrication. However, periodic cleaning/vacuuming of the fan/heater and around the air intake, located under the top shelf (Fig. 4), is recommended. Make sure the power is turned OFF before proceeding. Cleaning of the touchpad label at the bottom front of the unit is to be done only using a soft cloth, slightly dampened in water (if needed, a small amount of dish soap can be added to the water) and dried using a clean, dry soft cloth. Cleaning of the scr...
Otros modelos de este manual:chimeneas - HEF26 (924.93 kb)