Votos - 3, Puntuación media: 5
(
)
)
|
Resumen del manual
I/O I/O A 3 2 1 7 B 6 5 4 Fig. 10 HEF22 touchpad buttons. The fireplace features conveniently separate controls for flame effect and for heater control. This allows you to operate the unit in three (3) different modes: • As a full-featured fireplace - both flame effect and heater are on. This mode allows you to enjoy the look of the fire along with the heat output of a heater. I/O I/O 3 A B 6 5 4 2 1 7 8 Fig. 11 HEF26 and HEF33 touchpad buttons. (Button 8 does not apply to HEF22.) • As a visual effect - only flame effect is on, the heater is off. We recommend this mode for warm weather application, when you want the ambiance of a fire, without any heat output. • As a heater - only heater is on, while the flame effect is off. This mode allows you to use your fireplace as an electric heater, without any flame effect. Refer to Figures 10, 11 & 12 for locations of the buttons on both, the touchpad and remote control unit, described in the following operating instructions. Note that in both cases, button numbers as shown in the figures are the same. NOTE: When the flame or heater is activated by buttons 1 or 4 on either the remote control or touchpad control panel, the respective LED lights up to indicate and allow settings to be changed. After 20 seconds of inactivity, a feature of the fireplace is for the LED visuals on the touchpad control panel to go out. You must activate the fireplace electronics by depressing any buttons on the remote control or the touchpad control panel for the LED visuals to reappear before any settings can be made or changed. 3 1 4 2 5 7 8 6 Fig. 12 Remote control. NOTE: The overhead light function on the remote shown does not apply to HEF22. Flame Speed Control Your fireplace features a flame speed that can be controlled either by remote control or at the touchpad control panel. By depressing button 1 once, the flame effect will be activated and turn on. By repeatedly depressing buttons 2 or 3, you can decrease or increase the flame effect speed to achieve the desired flame effect. Refer to the visual indicator A to monitor the relative speed of the flame effect between the slowest (lowest light bar) and fastest (highest light bar). For your added convenience, the flame effect speed setting is stored in memory when the flame effect is turned off. Heater Control Wood Burning/Crackling Sound Effect Your fireplace features a heater with a built-in thermostat and a variable temperature setting that can be controlled either by remote control or at the touchpad control panel. By depressing button 4 once, the heater will be activated and the LED visual indicator B lights up to indicate the temperature setting of the heater between the lowest (lowest light bar) and highest (highest light bar). to determine the room temperature, depress button 5 or 6 to decrease or increase until the heater goes off or comes on. The heater is designed to safely deliver the maximum amount of heat when it is turned on. To increase the room temperature, depress button 6 to increase room temperature setting. when the set temperature is reached, the heater will automatically cycle on and off to maintain the temperature setting for the room. It is suggested that you increase the temperature setting gradually to a room temperature that you are comfortable with. For your added convenience, the temperature setting is stored in memory when the heater is turned off. Your fireplace features a realistic wood burning/crackling sound effect. Depressing button 7 switches the sound effect off or on while the flame is on. If the flame is switched off, the sound effect will go off but will come back on when the flame is switched back on. Overhead Light Your fireplace features overhead lights that add warmth and glow to the refractories and logs. It is turned on or off either by remote control or at the touchpad control panel. Depressing button 8 switches the overhead lights on or off while the flame is on. If the flame is switched off, the overhead lights will go off but will come back on when the flame is switched back on. This feature is not available on the HEF22. 10008388 13 11 216mm [8 1/2"] (DISTANCE BETWEEN TWO SOCKETS) 216mm [8 1/2"] (DISTANCE BETWEEN TWO SOCKETS} 305mm [12"] 1 3 2 4 5 6 7a 8 9 12 13 14 10 16 7b CFM Corporation reserves the right to make changes in design, materials, specifications, prices and discontinue colors and products at any time, without notice. HEF22/26/33 Electric Fireplace Ref. Description HEF22 HEF26 HEF33 1. Logset 10006656 10006711 10006532/10008135 (alt.) 2. Ember Lava Rock 10008060 10008059 10006526 3. Circuit Board 10007870 10007870 10007870 4. Refractory Right Side n/a 10007877 10008013 5. Refractory Left Side n/a 10007877 10008015 HEF22/26/33 Electric Fireplace (continued) Ref. Description HEF22 HEF26 HEF33 6. DC Motor 10001978 10001978 10001978 7a. Glass Door Assembly 10008175 n/a n/a 7b. Glass Door Assembly n/a 10008721 10008428 8. Glass Operable Door Assembly n/a 10008230 n/a 9. Gl...