Votos - 2, Puntuación media: 3.5
(
)
)
|
Resumen del manual
TOP 1PC ZZ.2822CWG.08 CORnER BOTTOM SUPPORT 1PC ZZ.2822CWG.09 CORnER UPRIGHT SUPPORT 1PC ZZ.2822CWG.10 BASE 1PC ZZ.2822CWG.01 LEFT FROnT PAnEL 1PC ZZ.2822CWG.05 InSIDE VIEW LEFT SIDE PAnEL 1PC ZZ.2822CWG.03 OUTSIDE VIEW FIREBOX SHELF 1PC ZZ.2822CWG.11 RIGHT FROnT RIGHT SIDE PAnEL 1PC PAnEL 1PC ZZ.2822CWG.04 ZZ.2822CWG.02 LOWER FACInG PAnEL 1PC ZZ.2822CWG.07 UPPER FACInG PAnEL 1PC ZZ.2822CWG.06 1 AnTI-TIP DEVICE 2 SETS WInGnUT AnD LOCK WASHER 2PCS 2PCS 4PCS 4PCS 4PCS CORnER ATTACHMEnT 1PC ZZ.2822CWG.08-1 20PCS 20PCS InCLUDES 1 SPARE GET REAdy To sTART GET REAdy To sTART Before assembly, use scissors to unwrap the parts from the packaging. DO NOT use a box cutter or exacto-knife as you may cut into the mantel pieces inside the box and damage the finish. Check for the hardware bag which is red and located inside the packaging, taped to the top box. Be sure you DO NOT discard any pieces. step 1 Locate the base and place it on the floor. Do not put it up against the wall at this point in the assembly, as you need to get in behind the mantel to insert several wingnuts, lock washers and firebox screws. step 2 Locate the left side panel and the left front panel. Facing the front of the base, take the left side panel, positioning it so the holes in the blocks on the bottom line up with the holes on the base. Position the left front panel next to the left side panel, lining up the holes in the blocks with the holes on the base. Attach the left front and side panel to the base by inserting and tightening 1 wingnut and 1 lock washer to each piece. Attach the left side and front panels together by inserting and tightening 3 wingnuts and 3 lock washers. step 3 Repeat Step 2, but with the right side panel and the right front panel. step 4 Locate the lower facing panel and the firebox shelf. Attach the lower facing panel by placing the granite side to the front then line up the holes on each side and insert 1 wingnut and 1 lock washer into each. Place the firebox shelf in behind, right up against the lower facing panel. step 5 Locate the granite upper facing panel that will be attached to the left and right legs and will sit above the firebox. Position this panel with the granite side facing the front of the mantel. Line up the holes on each side and insert and tighten 1 wingnut and 1 lock washer on each side. step 1 step 2 step 4 step 5 step 6 Getyourassistantandlocatethetopofyourmantel.Thistopisveryheavy.Itwilltake2peopletoliftandpositionitinplace.Ensurethetopgoesoverthepositioningguidelocatedontheheader.Thetopmustgooverthisguidetobepositionedcorrectly.Lineuptheholesonthetopofthemantel,insertandtighten5wingnutsandlockwashers. 2 step 6 step 7 step 7 If you are using this mantel in a corner application, locate the triangular piece of wood which attaches to the mantel to create the corner unit. You must attach this piece for all corner applications. Slide the corner bottom support into the channel located at the middle of the back of the hearth base. Place the top corner attachment on the floor upside down. Protect it from damage. Attach the corner upright support to the corner attachment by lining up the hole in the corner upright with hole in the corner top insert with 1 nut and 1 lock washer. Simply take the triangle and slide the brackets with the holes onto the pins which are already attached to the mantel. Once the triangle is attached, push it up so it is level with the mantel and lock it into place. To lock it into place simply turn the horizontal wooden blocks attached to the underside of the mantel into a vertical position to support the weight of the corner triangle. Now attach the corner bottom support to the corner upright support by insert and tightening 1 wing and 1 lock washer. step 8 Take your electric firebox out of its packaging and position it between the 2 legs of the mantel. Once you are close to the wall, plug the firebox into the nearest outlet. The firebox comes with 3 metal brackets and 20 black screws. These metal brackets must be attached to both the sides of the firebox and the mantel to ensure that your firebox does not move around as you use it. 2 of the brackets have 2 large holes on one side. These large holes line up with 2 screws on the side of the firebox. The other screws provided must be inserted into the holes at the other end of the bracket and into the firebox. The other side of each bracket attaches to the mantel. The 3rd bracket has no holes on 1 side. That side should go up against the firebox top but should not be attached as the heater sits right underneath the bracket. Only the mantel side should be attached. If you have any questions about the firebox please reference the installation instructions that come with the firebox. Please reference the Quick Tips section of that instruction manual. noTE: some fireboxes come with pre-attached trims step 9 You are now ready to position your mantel against the wall. This step requires 2 people to move the unit. Anti-tipping device step ...