Votos - 2, Puntuación media: 4
(
)
)
|
Resumen del manual
DO NOT use a box cutter or exacto-knife as you may cut into the mantel pieces inside the box and damage the finish. Check for the hardware bag which is red and located inside the packaging taped to the top box. Be sure you DO NOT discard any pieces. For the easiest assembly, use a power Phillips-head screwdriver. DO NOT over tighten the screws. Step 1 Locate the hearth and place it on the floor. Do not put it up against the wall at this point in the assembly as you need to get in behind the mantel to insert several screws. Step 2 Locate the left leg of the mantel. Facing the front of the hearth, take the left leg, positioning it so the holes in the blocks on the legs line up with the screw holes in the hearth. Insert the 1” screws into the smaller screw holes and tighten. Step 3 Locate the right leg of the mantel. Facing the front of the hearth, take the right leg, positioning it so the holes in the blocks on the legs line up with the screw holes in the hearth. Insert the 1” screws into the smaller screw holes and tighten. GET READY TO START Before assembly, use scissors to unwrap the parts from the packaging. DO NOT use a box cutter or exacto-knife as you may cut into the mantel pieces inside the box and damage the finish. Check for the hardware bag which is red and located inside the packaging taped to the top box. Be sure you DO NOT discard any pieces. For the easiest assembly, use a power Phillips-head screwdriver. DO NOT over tighten the screws. Step 1 Locate the hearth and place it on the floor. Do not put it up against the wall at this point in the assembly as you need to get in behind the mantel to insert several screws. Step 2 Locate the left leg of the mantel. Facing the front of the hearth, take the left leg, positioning it so the holes in the blocks on the legs line up with the screw holes in the hearth. Insert the 1” screws into the smaller screw holes and tighten. Step 3 Locate the right leg of the mantel. Facing the front of the hearth, take the right leg, positioning it so the holes in the blocks on the legs line up with the screw holes in the hearth. Insert the 1” screws into the smaller screw holes and tighten. Step 4 Take your electric firebox out of its packaging and position it between the 2 legs of the mantel. Ensure the plug is at the back of your mantel, ready to be plugged in before you position your mantel in place up against the wall. The firebox does not get attached to the mantel in any way ……… it just sits there. If you have any questions about the firebox please reference the installation instructions that come with the unit. Please reference the Quick Tips section of that instruction manual. Step 5 Locate the header piece that will be attached to the left and right legs and will sit above the firebox. Position the header with the finished side facing the front of the mantel. Insert and tighten the 4 screws which will hold the header in place. CAUTION DO NOT USE AN ELECTRIC DRILL TO INSERT THESE SCREWS. A POWER DRILL CAN DRIVE THE SCREWS THROUGH THE FACE OF THIS PANEL THIS SHOULD NOT HAPPEN WITH A MANUAL SCREW DRIVER. Step 6 Get your helper and locate the top of your mantel. This top is very heavy. It will take 2 people to lift and position it in place. Ensure the top goes over the positioning guide located on the header. The top must go over this guide to be positioned correctly. Once the top is in place insert and tighten the 9 screws which hold the top in place. Step 7 For assembly of the audio kit please refer to the audio kit manual in the subwoofer box. Follow the instructions and your system will be ready for your listening pleasure. Step 8 You are now ready to position your mantel against the wall. This step requires 2 people to move the unit. Once you are close to the wall, plug the firebox into the nearest outlet. Anti-tipping device At this point you must attach the anti-dipping device to your mantel and your wall. This device is a safety feature that will prevent your mantel from tipping over if a weight is applied which can unbalance the unit (like a child climbing onto it). WARRANTY DO NOT RETURN THIS PRODUCT TO THE STORE: Greenway Home Products is pleased to offer in home warranty repairs. Please contact Customer Service at: In Canada: 1-866-253-0447 In the USA: 1-866-282-0533 Limited Warranty Definitions Greenway Home Products: Manufacturer. Mantel: Mantel manufactured by Greenway Home Products. Purchaser: Purchaser of the Mantel Distributor: Facility authorized to sell Greenway Home Products. Warranty Card Greenway Home Products Limited Warranty Registration Card identifying the Purchaser and product model. Greenway Limited Warranty: Greenway ...