Votos - 3, Puntuación media: 3.7
(
)
)
|
Resumen del manual
Tools and Supplies Needed Before beginning the installation be sure that the following tools and building supplies are available. Reciprocating saw Framing material Pliers Hi temp caulking material Hammer Gloves Phillips screwdriver Framing square Flat blade screwdriver Electric drill and bits (1/4 in.) Plumb line Safety glasses C. Inspect Appliance and Components WARNING Inspect appliance and components for damage. Damaged parts may impair safe operation. • Do NOT install damaged components. • Do NOT install incomplete components. • Do NOT install substitute components. Report damaged parts to dealer. • Carefully remove the appliance and components from the packaging. • The vent system components and trim doors are shipped in separate packages. • The gas logs may be packaged separately and must be field installed. • Report to your dealer any parts damaged in shipment, particularly the condition of the glass. • Read all of the instructions before starting the installation. Follow these instructions carefully during the installation to ensure maximum safety and benefit. WARNING Hearth & Home Technologies disclaims any responsibility for, and the warranty will be voided by, the following actions: • Installation and use of any damaged appliance or vent system component. • Modification of the appliance or vent system. • Installation other than as instructed by Hearth & Home Technologies. • Improper positioning of the gas logs or the glass door. • Installation and/or use of any component part not approved by Hearth & Home Technologies. Any such action may cause a fire hazard. Level 1/2 - 3/4 inch length, #6 or #8 Self-drilling screws Manometer Voltmeter Tape measure Noncorrosive leak check solution One 1/4 inch female connection (for optional fan). Heat & Glo • Escape-36DV • 2012-900 • Rev. AB • 10/08 • D. Inspect Firebox Surface cracking or crazing of firebrick material is normal and expected. The following types of cracks are acceptable and do not require replacement of the unit or the firebox: • Cracks that do not propagate entirely thru the material. • Light fracture lines or “spider-webbing” on the surface of the material. • Cracks that are less than 1/32 in. wide and less than 3 in. long. • If cosmetically unacceptable, such cracks may be repaired with the SRV-PACK service kit. See Service Parts List. Cracks that are unacceptable: • Cracks greater than 1/32 in. wide and 3 in. long are at risk of growing. • Cracks that penetrate entirely through the firebrick material. Inspection for cracking should be run when the appliance is cool. Cracks tend to close as the appliance heats up. Heat & Glo • Escape-36DV • 2012-900 • Rev. AB • 10/08 3 33 Framing and Clearances Note: WARNING • Illustrations reflect typical installations and are FOR Fire Risk DESIGN PURPOSES ONLY. Provide adequate clearance: • Illustrations/diagrams are not drawn to scale. • Around air openings preference. • Actual installation may vary due to individual design • To combustibles • For service access A. Selecting Appliance Location Locate appliance away from traffic areas. When selecting a location for your appliance it is important to Note: For actual appliance dimensions refer to Sec consider the required clearances to walls (see figure 3.1). tion 16. D C E B A F In addition to these framing dimensions, also reference the following sections: • Clearances and Mantel Projections (Sections 3.C and 3.D) • Vent Clearances and Framing (Section 6). A B C D E F Inches 51-1/2 22 46-3/4 66 93-3/8 7-1/2 Millimeters 1308 559 1187 1676 2372 190 Figure 3.1 Appliance Locations Heat & Glo • Escape-36DV • 2012-900 • Rev. AB • 10/08 Heat & Glo • Escape-36DV • 2012-900 • Rev. AB • 10/08 9 Fire Risk. • Construct chase to all clearance specifi cations in manual. • Locate and install appliance to all clearance specifi cations in manual. B. Constructing the Appliance Chase A chase is a vertical boxlike structure built to enclose the gas appliance and/or its vent system. Vertical vents that run on the outside of a building may be, but are not required to be, installed inside a chase. Construction of the chase may vary with the type of building. These instructions are not substitutes for the requirements of local building codes. Local building codes MUST be checked. Chases should be constructed in the manner of all outside walls of the home to prevent cold air drafting problems. The chase should not break the outside building envelope in any manner. Walls, ceiling, base plate and cantilever fl oor of the chase should be insulated. Vapor and air infi ltration barriers should be installed in the chase as per regional codes for the rest of the home. Additionally, in regions where cold air infi ltration may be an issue, the inside surfaces may be sheetrocked and taped for maximum air tightness. To further prevent drafts, the wall shield and ceiling fi restops should be caulked with high temperature caulk to seal gaps. Gas line holes and other openings should be caulked...