Votos - 1, Puntuación media: 4
(
)
)
|
Resumen del manual
X 10 IN. (254 MM X 254 MM) INSIDE TO INSIDE 10 IN. (254 MM) Figure 6.5 Installing the Attic Shield 3 FASTENERS PER SIDE BEND TABS IN AROUND PIPE ATTIC SHIELD INSTALLED BELOW CEILING ATTIC SHIELD INSTALLED ABOVE CEILING Heat & Glo • 6000GCF-IPI, 6000GCF-IPILP • 2110-900 Rev. G • 9/08 20 Heat & Glo • 6000GCF-IPI, 6000GCF-IPILP • 2110-900 Rev. G • 9/08 7 Appliance Preparation A. Attaching Sheetrock Ledges Attach sheetrock ledges together using the attachment holes (see Figure 7.1). Figure 7.1 The sheetrock ledges will attach to the top of the unit (see Figure 7.2). Figure 7.2 Attach previous assembly to the top of the unit using the provided slots. The face of the sheetrock ledge assembly and the unit surround should be fl ush to each other. Figure 7.3 SEE DETAIL B CLEARANCE SLOT SHEETROCK LEDGE UNIT SURROUND ATTACHMENT HOLES 6 PLACES DETAIL B B. Temporary Access Panel Remove the lower access panel to run the electrical and gas lines to the unit (see Figure 7.3). Once the electrical and gas lines are hooked up, the lower access panel must be put back on the unit. LOWER ACCESS PANEL SEE DETAIL A DETAIL A ATTACHMENT HOLES NAILING TAB Heat & Glo • 6000GCF-IPI, 6000GCF-IPILP • 2110-900 Rev. G • 9/08 21 C. Securing and Leveling the Appliance The diagram shows how to properly position, level, and secure the appliance (see Figure 7.4). Nailing tabs are provided to secure the appliance to the framing members. • Place the appliance into position. • Level the appliance from side to side and front to back. • Shim the appliance, as necessary. It is acceptable to use wood shims. • Bend out nailing tabs on each side. • Keep nailing tabs fl ush with the framing. • Secure the appliance to the framing by using nails or screws through the nailing tabs. Figure 7.4 Proper Positioning, Leveling and Securing of Appliance NAILING TABS (BOTH SIDES) D. Installing the Flue Restrictor Figure 7.5 FLUE RESTRICTOR Figure 7.6 Flue Restrictor BREAK HERE 1. Break the Flue Restrictor into two pieces. Do this by bending the part back and forth until it breaks (see Figure 7.6). Fire Risk. • ALWAYS maintain specifi ed clearances around the appliance. • Do NOT notch into the framing around the appliance spacers. Failure to keep insulation, framing or other material away from the appliance may cause fi re. Fire Risk. • Prevent contact with sagging, loose insulation. • Do NOT install against combustible materials such as exposed insulation, plastic and insulation backer. WARNING WARNING 2. Match the amount of vertical in the system with the chart to find the appropriate position to set the Flue Restrictor (see Figure 7.7). Vertical 4’ 8’ 15’ 20’ 25’ 30’ 35’ 40’ 45’ 50’ Figure 7.7 - CHART Top Vent NG 1-1 2-2 3-3 3-4 3-4 4-4 4-4 5-4 5-4 5-4 Top Vent LP No Restrictor 1-2 3-2 3-3 3-3 3-4 3-4 4-4 4-4 4-4 3. Center the Flue Restrictor on vent and secure in place by using two self-tapping screws (see Figure 7.8). 1 2 3 4 5 SETTING 1 2 3 4 5 E. Installing the Fiberglass Gasket The fiberglass gasket supplied in the manual bag seals between the first 8 inch (203 mm) vent component and the outer fireplace wrap. Using 2 self-tapping screws from the manual bag secure the gasket to the outer wrap (see Figure 7.9). Figure 7.9 Fiberglass Gasket FIRST VENT COMPONENT FIBERGLASS GASKET OUTERWRAP Figure 7.8 Heat & Glo • 6000GCF-IPI, 6000GCF-IPILP • 2110-900 Rev. G • 9/08 8 88 Installing Vent Pipe A. Assembly of Vent Sections • Apply a bead of silicone sealant inside the female outer pipe joint prior to joining sections. See Figure 8.1 • Only outer pipes are sealed. Do not seal the inner flue. All unit collar, pipe, slip section, elbow and cap outer flues shall be sealed in this manner, unless otherwise stated. WARNING Do not mix pipe, fittings or joining methods from different manufacturers. WARNING Fire Risk Exhaust Fumes Risk Impaired Performance of Appliance • Overlap pipe slip sections at least 1-1/2 inches. • Use pilot holes for screws. • Screws must not exceed one inch long. • Pipe may separate if not properly joined. High Temperature Silicone SealantCommercial, Multi-family (multi-level exceeding two stories), or High-rise Applications only Figure 8.1 Lances Attaching Vent to the Firebox Assembly To attach the first pipe section to the collars, slide the male end of the inner vent of the pipe section over the inner collar on the firebox assembly. At the same time, slide the outer flue over the outer collar on the appliance. Push the pipe section into the appliance collar until all the lances (see Figure 8.1) have snapped in place. Tug slightly on the section to confirm it has completely locked into place. Assembling Pipe Sections Insert the inner flue of section A into the flared inner flue of section B. Start the outer flue of section A over the outer flue of section B (see Figure 8.2). Note: The end of the pipe sections with the lances/tabs on it will face towards the appliance. Once both inner and outer flues are started, press section A onto section B firmly...
Otros modelos de este manual:chimeneas - 6000GCF-IPI (3.22 mb)