Votos - 4, Puntuación media: 3
(
)
)
|
Resumen del manual
The bay front is a decorative overlay only. 1) Place the bay door onto the 2 pins on the top of the unit. 2) Position 2 magnets on the back of each trim piece close to the ends. Place the top and bottom trim pieces on the bay front. 3) Install top and bottom louvers. Note: Top and bottom louvers and brackets are different. See diagram below. 2) Install bottom louver by sliding the two bracket clips into the brackets located underneath the bay door and secure with 2 screws into the bracket on the bottom of the Bay Front as per diagram 1. INSTALLATION FLUSH LOUVERS 1) The Top Louver is held in place by Spring Clips. Push into place as shown. 2) Install the Spring Hinges on the left and right side of the bottom of the Firebox using 2 screws per hinge. 3) Place the Bottom Louver near the hinge. Flip hinge over the Bottom Louver and secure using 3 screws. Bottom Louver Hinge Location INSTALLATION Conversion Kit from Natural Gas to Propane Model #533-969 THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !! 1) Turn the unit off and allow it to cool to room temperature. 2) Shut off gass supply 3) Unplug or disconnect power source to stove. 4) Remove glass front (see manual). 5) Remove logs and brick panels (if installed). 6) Remove the Grate by removing the screws on each side of the grate. Remove the 2 screws holding the grate in position. 7) Remove the Burner Tray by removing 1 screw on each side of the tray, then slide the tray to the left and lift out. Remove the 2 screws, push Burner Tray to the left, and lift off. 8) Pull off the pilot cap to expose the pilot orifice. 9) Unscrew the pilot orifice with the allen key (provided) and replace with the LP pilot orifice in the kit. 10) Remove burner orifice with 1/2" wrench. Use another wrench to hold onto the elbow behind the officeReplace with the #54 orifice in the Kit. Burner Orifice Regency E21 Gas Fireplace Insert INSTALLATION 11) Remove and discard the 3 pressure regulator mounting screws (A), pressure regulator tower (B) and diaphragm (C). 12) Insure that the rubber gasket (D) is properly positioned and install the new HI/LO pressure regulator assembly to the valve using the new screws (E) supplied with the kit. Tighten screws securely. 13) Replace Burner Tray and reverse steps 6) to 1). 14) Adjust the burner aeration setting from 1/8" to 3/16" as required for the best flame picture. 15) Remove the switch cover from the left side of the body base and pull the thermodisc out of the bracket under the left side of the firebox bottom and replace with the Thermodisc supplied with this kit. Remove the 2 nuts holding the switch box in place, then pull the thermosdisc out of the bracket. 16) Attach clear label "This unit has been converted to Propane" near or ontheserial#decal.Attachwhitelabel "Thisvalvehasbeenconverted from NG to LPG using SIT conversion Kit Code 0.907.202" onto the valve. 17) Replace yellow "Natural Gas" label with red "Propane" label 18) Check for gas leaks. 19) Check inlet and outlet pressures. 20) Check operation of flame control. 21) Check for proper flame appearance and glow on logs. Regency E21 Gas Fireplace Insert INSTALLATION FULL SCREEN FRONT 1) Hold the full screen door up against the unit in order to make the 3) Completely secure full screen door to the unit by securing 4 screws following wire connections. to the Left and Right Side Trim. Pull the ON/OFF connector wires thru the box and connect them to the switch. Connect the fan switch wires with the wire connectors from the fan speed control. Place clips over wires and tuck into side trim. 4) Secure the Top Frame by sliding it on the screws at the top of the full screen door. It is held in place by magnets. 2) Lift the unit up slightly and push down on the corners of the Bottom Trim Bracket and slide under unit. Bottom Trim Bracket Push in Corners Screw Top Frame Regency E21 Gas Fireplace Insert INSTALLATION 5) Install Spring Hinges to the Left and Right Side of the bottom of the firebox using 2 screws per hinge. 6) Place Bottom Frame near hinge. Flip hinge over Bottom Frame and secure with 3 screws each. Bottom Frame Hinge Location 7) Install the Left and Right Side Screen Doors by placing over top of the hinges on the faceplate. Hold the door at a 45 degree angle to avoid scratching the faceplate. Hinge Screen Door 8) Close screen doors. Regency E21 Gas Fireplace Insert INSTALLATION Option 1: REMOTE CONTROL Use the Regency Remote Control Kit approved for this unit. Use of other systems may void your warranty. The remote control kit comes with a hand held transmitter, a receiver and a wall mounting plate. 1) Choose a convenient location on the wall to install the receiver and the receptacle box (protection from extreme heat is very important). Run wires from the fireplace to that location. Use Thermostat Wire Table. 2) Connect the two wires to the gas valve. See diagram below. CAUTIONDo not wire millivolt remote control wires to 120V wire. 3...
Otros modelos de este manual:chimeneas - E21-LP1 (10.31 mb)