Votos - 4, Puntuación media: 4.3
(
)
)
|
Resumen del manual
1) Install the Sub-Frame by hooking the top flange onto the top of the Glass Door and swing the Sub-Frame towards the unit. Pull out the hooks which already secure the Glass Door and place them thru the holes in the bottom of the Sub-Frame to secure both the Glass Door and Sub-Frame in place together. Sub-Frame Glass Door Hook Sub-Frame 2) Mount the 2-panel Door Frame to the flange on Sub-Frame, ensuring to line up holes. Secure using the 6 screws provided. 3) Hook the Left Side Screen Door to the Door Frame by placing the door hinges (top & bottom) over the pins on the Door Frame. Repeat for Right Side Screen Door. Note: It will be easier to put the Screen Door in place by starting with the bottom hinge. Left Side Door Pin on Door Frame Note: If you find that the Left or Right Side Screen Door is lower then Glass Door Sub-Frame Sub-Frame Hook 2) Mount the 3-panel Screen Door / Frame Assembly to the fl ange on Sub-Frame, ensuring to line-up holes. Secure using the 4 screws provided. the other, use the spacer provided to help align the Doors. The spacer is to be placed over the bottom pin before installing the Screen Door. U35 FPI Direct Vent Gas Insert INSTALLATION FULL SCREEN DOORS 1) Hold the full screen faceplate up against the unit in order to make 3) Completely secure faceplate to the unit by securing 4 screws to thethe following wire connections. Left and Right Side Trim. Pull the ON/OFF connector wires thru the box and connect them to the switch. Connect the fan switch wires with the wire connectors from the fan speed control. Place clips over wires and tuck into side trim. 4) Secure the Top Frame by sliding it on the screws at the top of the full screen door. It is held in place by magnets. Push in Corners Bottom Trim Bracket 2) Lift the unit up slightly and push down on the corners of the Bottom Trim Bracket and slide under unit. Screw Top Frame U35 FPI Direct Vent Gas Insert INSTALLATION 5) Install Spring Hinges to the Left and Right Side of the bottom of the 7) Install the Left and Right Side Screen Doors by placing over top of firebox using 2 screws per hinge. the hinges on the faceplate. Hold the door at a 45 degree angle to avoid scratching the faceplate. Hinge 6) Place Bottom Frame near hinge. Flip hinge over Bottom Frame and secure with 3 screws each. Screen Door 8) Close screen doors. Bottom Frame Hinge Location U35 FPI Direct Vent Gas Insert INSTALLATION WIRING DIAGRAMS This heater does not require a 120V A.C. supply Caution: Ensure that the for operation. However, a 120V A.C. power wires do not touch any supply is needed for the fan/blower operation. hot surfaces and are away from sharp edges. WARNING: Electrical Grounding Instructions This appliance is equipped with a three pronged (grounding) plug for your protection against shock hazard and should be plugged directly into a properly grounded three-prong receptacle. Do not cut or remove the grounding prong from this plug. CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. For NATURAL GAS Units and Units NOT Equipped with DC Spark Boxes U35 FPI Direct Vent Gas Insert U35 FPI Direct Vent Gas Insert 19 Use the FPI Remote Control Kit approved for this unit. Use of other systems may void your warranty. The remote control kit comes with a hand held transmitter, a receiver and a wall mounting plate. 1) Choose a convenient location on the wall to install the receiver and the receptacle box (protection from extreme heat is very important). Run wires from the fi replace to that location. Use Thermostat Wire Table. 2) Connect the wires as per the wiring diagrams below. CAUTION Do not connect the millivolt remote control wires to the 120V wires. 3) Install 3 AAA alkaline batteries in transmitter and 4 AA alkaline batteries in the receiver. Install the receiver and its cover in the wall. Switch the remote receiver to "remote" mode. The remote control is now ready for operation. OPTIONAL REMOTE CONTROL OPTIONAL WALL THERMOSTAT A wall thermostat may be installed if desired, follow the wiring diagram below. Note: the wires are connected to the "TH" on the gas valve. Use the table below to determine the maximum wire length. FPI offers an optional programmable thermostat but any 250-750 millivolt rated nonanticipator type thermostat that is CSA, ULC or UL approved may be used. It is recommended that the thermostat be installed on an interior wall. CAUTION Do not connect the millivolt wall thermostat wires to the 120V wires. INSTALLATION For PROPANE Units and Units Equipped with DC Spark Boxes OPERATING INSTRUCTIONS Thermostat Wire Table Recommended Maximum Lead Length (Two-Wire) When Using Wall Thermostat (CP-2 System) Wire Size Max. Length 14 GA. 50 Ft. 16 GA. 32 Ft. 18 GA. 20 Ft. 20 GA. 12 Ft. 22 GA. 9 Ft. FINAL CHECK Before leaving this unit with the customer, the installer must ensure that the appliance is firing correctly. This includes: 1) Clocking the appliance to ensu...
Otros modelos de este manual:chimeneas - Gas Insert U35-LP1 (3.81 mb)