Votos - 3, Puntuación media: 4
(
)
)
|
Resumen del manual
WARNING:Construction and electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire, electric shock and injury to persons. WARNING:Do not attempt to wire your own new outlets or circuits. To reduce the risk of fire, electric shock or injury to persons, always use a licensed electrician. Make sure the units Main On/1. Off switch is switched Off (refer to operating instruction section). Plug the unit directly into a 15 2. Amp/120 Volt outlet. Operation Figure 1 A B C To access the controls go to the back of the Stove (Figure 1). A. Three Position On/Off Switch The switch has two On positions marked with “-” and “=”. The “-” position is for manual operation. In this position, the built-in remote control is bypassed. The “=” position is for operating the unit with the provided remote control. When in “=” position the unit is operated with the ON and OFF buttons of the remote control. When the switch is in the center position the unit is off. B. Heater On/Off Switch The Heater On/Off Switch supplies power to the heater fan and the heater element. C. Heater Thermostat Control To adjust the temperature to your individual requirements, turn the thermostat control clockwise all the way to turn on the heater. When the room reached the desired temperature, turn the thermostat knob counter clockwise until you hear a click. Leave in this position to maintain the room temperature at this setting. For additional heat, turn clockwise until you hear the click again and the heater will turn on. To turn the heater off, switch the Heater On/Off Switch to the Off position. ! NOTE: When the heater is switched On, the heater fan will operate. The heater element may or may not be on, depending on the thermostat control setting. Resetting The Temperature Cutoff Switch Should the heater overheat, an automatic cut out will turn the heater off and it will not come back on without being reset. It can be reset by switching the Main On/Off Switch to Off and waiting 5 minutes before switching the unit back on. CAUTION: If you need to continuously reset the heater, unplug the unit and call Dimplex North America Limited at 1-888- 346-7539. Remote Control (Figure 2) The stove is supplied with an integrated On/Off remote control, that is factory syncronized with the stove. To operate, push the ON button to turn stove on, push the OFF button to turn the stove off. The amount of heat produced will be dependant on positioning of manual heat controls. ! Note: Ensure that the stove’s On/Off switch is set to the remote control setting (“ II ” position). Initialization/Reprogramming Follow these steps for remote control initialization if required: . Set the main power switch to OFF. . Set the 3 Position Switch to the Remote position (refer to Operation Section). . Wait a minimum of five (5) seconds and then turn the main power ON. . Within 10 seconds of re- acquiring power, press the ON button located on the remote control transmitter. ! NOTE: You will have only 10 seconds to perform this last Operation Figure 2 ON Button OFF Button Battery Battery Cover step. Failure to do so will result in these steps needing to be followed again. This will synchronize the remote control transmitter and receiver. Operation Battery Replacement . Slide battery cover open on the hand held transmitter (Figure 4). . Correctly install one (1) 12 Volt (A23) battery in the battery holder. . Close the battery cover. Maintenance WARNING: Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electric shock or damage to persons. Light Bulb Replacement CAUTION: Allow at least five (5) minutes for light bulbs to cool off before touching bulbs to avoid accidental burning of skin. Light bulbs need to be replaced when you notice a dark section of the flame or when the clarity and detail of the log exterior disappears. There are two bulbs under the log set which generate the flames and embers. Tool Requirements: Phillips screw driver Helpful Hints It is a good idea to replace all light bulbs at one time if they are close to the end of their rated life. Group replacement will reduce the number of times you need to open the unit to replace light bulbs. Upper Light Bulb Requirements Quantity of one (1) clear chandelier or candelabra bulbs with an E-12 (small) socket base, 7 Watt rating. Upper Bulb Replacement Open door by pulling the 1. handle. Locate the upper bulb 2. bracket.Bend light retainer bracket down.Locate and remove the light bulb.Insert new bulb. Bend light retainer bracket 3. back into its original position. Close the door.4. Lower Light Bulb Requirements Quantity of two (2) clear chandelier or candelabra bulbs with an E-12 (small) socket base, 60 Watt rating. Lower Bulb Replacement Open door by pulling the 1. handle.Remove the screw from the log set located in the center of the ember bed and remove the log set from the unit. Locate and examine the bulbs 2. to determine wh...
Otros modelos de este manual:chimeneas - DS5603 (522.62 kb)
chimeneas - DS5804CM (522.62 kb)