Votos - 3, Puntuación media: 4.7
(
)
)
|
Resumen del manual
HORIZONTAL AIR TERMINAL INSTALLATION 4. Apply high temperature sealant W5730002 (not supplied) to the outer edge of the of the outside sleeve of the air terminal. Slip a 8" diameter coupler over the sleeve and secure as before. Trim the 8" coupler even with the 5" coupler end. 5. Thread the air terminal pipe assembly down through the roof support and attach, ensuring that a minimum 16" of air terminal FIGURE 29 FIGURE 27 will penetrate the roof when fastened. If the C CCA AAU UUL LLK KKI IIN NNG GG attic space is tight, we recommend thread # ##1 110 00x xx2 22. .." "" ing the Wolf Steel vent pipe collar or equivalent loosely onto the air terminal CCAAUULLKKIINNGGSSCCRREEWWSS 8 88" ""P PPI IIP PPE EE 5 55" ""P PPI IIP PPE EE assembly as it is passed through the SSEEAALLAANNTTHHII--TTEEMMPPAATTTTEECCAAUUTTNNTTIIOOIIOONNNN--CC--HHAAHHUUDDOOTT FIGURE 30 attic. The air terminal must be located 2 22" ""O OOV VVE EER RRL LLA AAP PP vertically and plumb. 6. Remove nails from the shingles, H HHI II- --T TTE EEM MMP PP T TTE EER RRM MMI IIN NNA AAL LL S SSE EEA AAL LLA AAN NNT TT E EEX XXT TTE EEN NNS SSI IIO OON NN P PPL LLA AAT TTE EE 1. Move the fireplace into position. Measure the vent length required between terminal and fireplace taking into account the additional length needed for the finished wall surface and any 1." overlaps between venting components. 2. Secure the terminal to the terminal extension plate. 3. Apply high temperature sealant W573-0007 (not supplied) to the outer edge of the 5" inner collar of the fireplace. Attach the first vent component and secure using 3 self tapping screws. Repeat using 8" piping. 4. Holding the air terminal (with the air deflectors to the top and the lettering in an upright, readable position) insert into both vent pipes with a twisting motion to ensure that both the terminal sleeves engage into the vent pipes and sealant. Secure the terminal extension plate to the exterior wall and make weather tight by sealing with caulking (not supplied). EXTENDED HORIZONTAL AIR TERMINAL INSTALLATION 1. Follow the instructions for "Horizontal Air Terminal Installations", above and to the sides of the chimney. Place the flashing over the air terminal and slide it underneath the sides and upper edge of the shingles. Ensure that the air terminal is properly centred within the flashing, giving a 3/4" margin all around. Fasten to the roof. Do NOT nail through the lower portion of the flashing. Make weather- tight by sealing with caulking. Where possible, cover the sides and top edges of the flashing with roofing material. 7. Aligning the seams of the terminal and air terminal connector, place the terminal over the air terminal connector making sure the inner sleeve goes into the hole in the terminal. Secure with the 3 screws provided. 8. Apply a heavy bead of weatherproof FIGURE 31 caulking 2" above the flashing. Note: Maintain a minimum 2" space between the air inlet base and the storm collar. Install the storm collar around the air terminal connector and slide down to the caulking. Tighten to ensure that a weather-tight seal between the air terminal connector and the collar is items 1 to 4. 2. Continue adding components alternating inner and outer venting. Ensure that all 5" venting and elbows have sufficient vent spacers attached and each component is securely fastened to the one prior. Attach the 5" telescopic sleeve to the vent run. Repeat using a 8" telescopic sleeve. Secure and seal as before. To facilitate completion, attach 5" and 8" couplers to the air terminal. FIGURE 28 3. Install the air terminal. See item 4 of the Horizontal Air Terminal Installation. Extend the 5" telescopic sleeve; connect to the air terminal assembly. Fasten with self tapping screws and seal. Repeat using the 8" telescopic sleeve. achieved. 9. Continue adding rigid venting sections, sealing and securing as above. Attach a 5" collapsed telescopic pipe to the last section of rigid piping. Secure with screws and seal. Repeat using a 8" telescopic pipe. 10. Run a bead of high temperature sealant around the outside of the 5" collar on the fireplace. Pull the adjustable pipe a minimum of 2" onto the collar. Secure with 3 screws. Repeat with the 8" telescopic pipe. 11. In the attic, slide the vent pipe collar down to cover up the open end of the shield and tighten. This will prevent any materials, such as insulation, from filling up the 1" air space around the pipe. RESTRICTING VERTICAL VENTS RESTRICTOR PLATE TOP OF THE FIREBOX FLUE COLLAR FIGURE 32 VERTICAL VENTING INSTALLATION 1. Move the fireplace into position. 2. Fasten the roof support to the roof using the screws provided. The roof support is optional. In this case the venting is to be adequately supported using either an alternate method suitable to the authority having jurisdiction or the optional roof support. 3. Apply high temperature sealant W573-0002 (not supplied) to the outer edge of the inner sleeve of the air terminal. Slip a 5" diameter coupler ...
Otros modelos de este manual:chimeneas - BCDV48N (2.39 mb)