Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
Use supports or equivalent non-combustible strapping to maintain the 1" clearance from combustibles. 1. Fasten the roof support to the roof using the screws provided. The roof support is optional. The venting is to be adequately supported using either an alternate method suitable to the authority having jurisdiction or the optional roof support. 2. Slip a 4" diameter length of aluminum flexible liner a minimum of 2" over the inner sleeve of the air terminal. Secure to the sleeve using 3 screws and flat washers. Seal the joint and screw heads using red RTV high temperature sealant Mill Pac (not supplied). Repeat using a 7" diameter length of rigid piping. If the attic space is tight, we recommend adding sufficient lengths of 7" rigid piping, secured and sealed as necessary. 3. Thread the air terminal pipe assembly down through the roof support and attach, ensuring that a minimum 16" of air terminal will penetrate the roof when fastened. The air terminal must be located vertically and plumb. 4. Remove nails from the shingles, above and to the sides of the chimney. Place the flashing over the air terminal and slide it underneath the sides and upper edge of the shingles. Ensure that the air terminal is properly centered within the flashing, giving a 3/4" margin all around. Fasten to the roof. Do NOT nail through the lower portion of the flashing. Make weather-tight by sealing with caulking. Where possible, cover the sides and top edges of the flashing with roofing material. 5. Apply a heavy bead of waterproof caulking 2 inches above the flashing. Slide the storm collar around the air terminal and down to the caulking. Tighten to ensure that a weather-tight seal between the air terminal and the collar is achieved. Attach the other storm collar centered between the air intake and air exhaust slots onto the air terminal. Tighten securely. 6. Attach the vertical rain cap. 7. In the attic, slide the vent pipe collar down to cover up the open end of the shield and tighten. This will prevent any materials, such as insulation, from filling up the 1" air space around the pipe. FIGURE 18 FIGURE 19 FIGURE 20 HORIZONTAL VENTING INSTALLATION VERTICAL VENTING INSTALLATION All inner exhaust and outer intake vent pipe joists may be sealed using either Red RTV high temp silicone sealant or Black high temp Mill Pac with the exception of the fireplace exhaust flue collar which must be sealed using Mill Pac (not supplied). 11 W415-0514 / 05.30.05 In Canada, mobile home installation may be vented horizontally or vertically. In the United States, it may only be installed vertically. See "Vertical Venting" or "Horizontal Air Terminal Installation" for installation. The fireplace is equipped with two 5/16" d i a m e t e r holes located near each corner of the base. For mobile home ins t a l l a t i o n s , the fireplace must be fastened in place. Use #10 screws, inserted through the holes in the base to secure. It is recommended that the fireplace be secured in all installations. 1. Attach the adjustable pipe to the last section of rigid piping. Secure with screws and seal. 2. Install the 4" aluminum flexible liner to the stove. Secure with 3 screws and flat washers. Seal the joint and screw holes using Mill Pac high temperature sealant not supplied. 3. Run a bead of red RTV high temperature sealant around the inside of the air intake collar. Pull the adjustable pipe a minimum 2" into the air intake collar. Ensure that the sealant is not visible on the exterior pipes once installation is completed. An optional decorative brass band is available for this use. (Standard with a GD175 kit). In the event that the venting must be disassembled, care must be taken to reseal the venting. FIGURE 22 Continue with "Gas Installation" Page 14 STOVE VENT CONNECTION MOBILE HOME INSTALLATION 2" OVERLAP SPEED SWITCH 14-5/32" SCREWS SELF DRILLING #8x1/2" 5-3/4" VARIABLE ON/OFF SWITCH SEALANT HI-TEMP FIGURE 21 12 W415-0514 / 05.30.05 Follow the instructions for "Wall and Ceiling Protection". ADAPTER INSTALLATION FIGURE 27 1. Remove the spill switch bracket from the rear of the adapter. 2. Gently pull the two wire terminals (located inside the 7" flue collar at the top of the stove) out approximately 8 inches. 3. Bring the wires through the lower hole in the adapter and out the spill switch opening. To pass the wires through the hole more easily, temporarily tape the two terminals together. 4. With the spill switch opening aligned to the back of the stove, take hold of the adaptor base and push the crimped edge into the stove flue collar. 5. Connect the wire terminals to the spill switch and resecure the bracket. For aesthetics, the adapter has been designed to accept a standard matte black 7" stove pipe and the Continental decorative brass band (standard with the GS150KT). Both are available from your Continental dealer. For ease of assembly, a 7" telescoping stove pipe may be installed over the 4" vent connection of the adapter. Add vent sections, twist...
Otros modelos de este manual:chimeneas - CDVS500-N (3.42 mb)