Votos - 4, Puntuación media: 4
(
)
)
|
Resumen del manual
Place control knob provided on shaft. 7. Turn on power to duplex outlet if previously turned off per the warning above. 8. Plug in blower power cord. a. If your firebox is installed as a freestanding unit with an accessory mantel, determine whether power cord will exit left side or right side of firebox. Route power cord through exit hole and plug power cord into a wall receptacle near firebox. b. If your firebox installation is recessed and/or pre-wired, plug power cord into duplex outlet provided. Refer to your firebox owner’s manual for instructions on wiring duplex outlet. CAUTION: Never touch the blower wheel while in operation. Blower Location Lower Firebox Cavity Side View Spade Terminals Magnetic Strips Exhaust Port Green Ground Wire Screw Figure 26 - Blower Model BK Speed Control Switch Bracket Blower Plug-In Control Shaft Duplex Outlet (Located under- neath firebox floor against lower right outside wall) Control Knob Locknut Figure 27 - Attaching Speed Control to Firebox 9. Check to make sure power cord is completely clear of blower wheel and there are no other foreign objects in blower wheel. Turn blower on and check for operation. Turn blower off by turning knob fully counterclockwise before continuing. 10. Peel off backing paper and stick supplied wiring diagram decal on firebox bottom approximately 12" in front of blower (see Figure 28). Model BKT Installation Note: When installing BKT thermostatically- controlled blower, you must first secure thermal switch bracket to blower if it has not already been factory installed. 1. Place green ground wire with ring terminal between bottom hole on thermal switch bracket and top ear hole on blower assembly. Insert phillips screw into all three pieces and tighten securely (see Figure 29). 2. Connect wire harness and power cord terminals. Connect blue jumper wire to blower motor terminal and right side terminal of thermal switch. Connect black wire to left side of thermal switch and white wire to other remaining blower motor terminal. Note: Power cord outer insulation sleeve may have to be stripped slightly to allow enough wire length to reach and make all connections. DO NOT trim excessive length away. Just enable enough to make all connections securely. 3. Place blower against lower rear wall of firebox outer wrapper with exhaust port directed upward and thermodisc positioned up near fireplace bottom. Thermodisc must be oriented near fireplace bottom as shown in Figure 29 in order to sense temperature and properly operate. Blower will be held in position against back wall by magnets incorporated onto blower housing (see Figure 29). 4. Be certain that all wire terminals are securely attached to terminals on blower motor and thermal switch, and that screw for thermodisc bracket and green ground wire is tight. 5. Mount speed control box against mounting plate provided in lower fireplace cavity by placing plastic control shaft forward through round hole (see Figure 27, page 18). 6. While supporting speed control, secure control shaft with lock nut by pushing and turning lock nut with pliers clockwise until it is tight against mounting plate. Place control knob provided on shaft (see Figure 27, page 18). 7. Check to make sure power cord is completely clear of blower wheel and that no other foreign objects are in blower wheel. Also double check all wire leads and make sure wire routing is not pinched or in a precarious position. Correct accordingly. 8. Turn on power to duplex outlet if previously turned off per warning in column 1, page 18. 9. Plug in blower power cord to duplex outlet. 10. Blower will only run when speed control knob is in ON position and thermal switch senses temperature after fireplace begins to heat up. Blower speed can be adjusted by rotating control knob. To turn off, turn knob fully counterclockwise until it clicks off. If blower is ON and has been running with fireplace operating, blower will continue to run for a short time after fireplace has been turned off. As thermal switch cools down, blower shuts down automatically. Fireplace Installation Continued Wiring Diagram Decal 12" in Front of Burner Figure 28 - Location of Wiring Diagram Decal (Model May Vary from Illustration) Power Cord White Wire Blue Wire Thermal Switch Bracket Magnetic Strips Air Flow Direction Black Wire Ring Terminal on Green Wire Thermal Switch Phillips Screw Air Flow Direction Magnets Thermodisc Route BKT Blower Through This Area Side View Firebox Bottom Blower Figure 29 - Blower Model BKT 11. Peel off backing paper and stick supplied wiring diagram decal on firebox bottom approximately 12" in front of blower (see Figure 28, page 19). Blower Wiring Diagram CAUTION: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation. Verify proper operation after servicing. Installing Gas Piping to Fireplace Location WARNING: A qualified service person must connect fireplace to gas supply. Follow all local co...
Otros modelos de este manual:chimeneas - (V)T32EN SERIES (1.73 mb)